Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)
RM32H0E _52 Drivetrain _060137 DRIVE SHAFT / PROPELLER SHAFT _0294913 FRONT DRIVE SHAFT ASSEMBLY(for TMC Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for TMC Made)  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.
C286096

Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot clamp and separate the front No. 2 axle inboard joint boot clamp.


Hide 43448F 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

a.
C286098

Using a screwdriver, release the staked part of the front axle inboard joint boot clamp and separate the front axle inboard joint boot clamp.


Hide 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 43030 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C158439C17
1.385,1.24 1.125,0.458 1.125,0.458 1.927,0.667 true 0.948,0.365 1.344,0.521 0.396,0.156 10 *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.
C265836

Remove the front axle inboard joint grommet from the front drive inboard joint assembly.


e.
C160822

Using a snap ring expander, remove the front drive inner shaft inner shaft snap ring from the front drive outboard joint shaft assembly.


f.
C316793C05
3.031,1.177 2.208,1.844 2.208,1.844 3.083,1.26 true 2.031,1.771 2.344,1.927 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch to make the matchmarks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




h.

Remove the front No. 2 axle inboard joint boot clamp, front drive inboard joint boot and front axle inboard joint boot clamp.


Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474E 6.REMOVE FRONT DRIVE SHAFT DAMPER LH

a.
C310867

Using needle-nose pliers, separate the 2 front drive shaft damper clamps.


b.

Remove the front drive shaft damper LH and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.


Hide 43474D 7.REMOVE FRONT DRIVE SHAFT DAMPER RH (for 2WD)

HINT:

Use the same procedure for the LH side.


Hide 43447F 8.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.
C286102

Using a screwdriver, release the staked part of the front No. 2 axle outboard joint boot clamp and separate the front No. 2 axle outboard joint boot clamp.


Hide 43447E 9.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.
C286103

Using a screwdriver, release the staked part of the front axle outboard joint boot clamp and separate the front axle outboard joint boot clamp.


Hide 10.REMOVE FRONT AXLE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the front drive outboard joint shaft assembly.


Hide 41336E 11.REMOVE FRONT DRIVE SHAFT DUST COVER LH

HINT:

Only perform the following procedure if the front drive shaft dust cover is deformed.


a.
C235586E01
1.885,1.448 2.698,1.688 true 2.74,1.615 3.198,1.813 0.458,0.198 10 false SST

Using SST and a press, remove the front drive shaft dust cover LH.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the front drive inboard joint assembly.

·

Do not overtighten SST.




Hide 41336D 12.REMOVE FRONT DRIVE SHAFT DUST COVER RH

HINT:

Only perform the following procedure if the front drive shaft dust cover is deformed.


a.

for 2WD:

i.

Perform the same procedure as for the LH side.



b.

for AWD:

i.
C067101

Using a press, remove the front drive shaft dust cover RH.

NOTICE:

Be careful not to drop the front drive inboard joint assembly.




Hide 13.REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)

a.

for AWD:

i.
C092033

Using a snap ring expander, remove the shaft snap ring.


ii.
C310850E02
1.969,1.5 2.281,1.823 false 1.958,1.49 2.281,1.823 false 2.323,1.76 2.646,1.958 0.323,0.198 10 false SST

Using SST and a press, remove the front drive shaft bearing.

SST
09527-10011  

NOTICE:

Be careful not to drop the front drive inboard joint assembly.