Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1436  Yaw Rate Sensor Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) detects improper installation of the yaw rate and acceleration sensor (airbag sensor assembly) or an abnormality in the difference between the yaw rate sensor value and the control value estimated based on the acceleration sensor, steering angle sensor and speed sensor signals.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1436 Yaw Rate Sensor Malfunction Difference between the yaw rate sensor value and the control value estimated inside the skid control ECU (brake actuator assembly) is abnormal.
·

Sensor installation

·

Yaw rate sensor (airbag sensor assembly)



PROCEDURE

1.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Yaw Rate Sensor Yaw rate sensor Min.: -128 °/s, Max.: 127 °/s Vehicle stopped: 0 °/s
Turning right: -128 to 0 °/s
Turning left: 0 to 127 °/s
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Yaw Rate Sensor
50003 105 24

d.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

Result:
Result Proceed to
NG (The yaw rate and acceleration sensor (airbag sensor assembly) output value is 0 °/s when the vehicle is stationary, but the value fluctuates when turning.) A
NG (The yaw rate and acceleration sensor (airbag sensor assembly) output value is not 0 °/s when the vehicle is stationary.) B
OK C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

2.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION

B

C

2.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
a.

Turn the ignition switch off.


b.

Drive the vehicle straight ahead at 50 km/h (31 mph) or more for at least 30 seconds.


c.

Check that the steering wheel is correctly centered while driving straight ahead.

HINT:

If front wheel alignment and steering are adjusted as a result of an off-center steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.


OK:

The steering wheel is correctly centered.



Result:
Proceed to
OK
NG



OK

3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING

3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The airbag sensor assembly is tightened to the specified torque.

The airbag sensor assembly is not be installed in a tilted position.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG