Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C360725C01
0.125,0.146 0.427,0.354 0.302,0.208 10 false *a
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -


Terminal No. (Symbol) Terminal Description
1 (+BM) ABS motor relay power supply
2 -
3 -
4 - (Not used)
5 (CANH) CAN communication line H
6 (CSW) VSC OFF switch input
7 (FL-) Front wheel speed LH (-) signal input
8 - (Not used)
9 - (Not used)
10 (STPO) Stop light control relay output
11 - (Not used)
12 -
13 -
14 (GND2) Pump motor ground
15 -
16 -
17 (FSW+)* Brake pedal load sensing switch input
18 - (Not used)
19 (CANL) CAN communication line L
20 - (Not used)
21 (FR+) Front wheel speed RH (+) signal input
22 (RR+) Rear wheel speed RH (+) signal input
23 (RL-) Rear wheel speed LH (-) signal input
24 (FL+) Front wheel speed LH (+) signal input
25 - (Not used)
26 (FR-) Front wheel speed RH (-) signal input
27 - (Not used)
28 - (Not used)
29 - (Not used)
30 (+BS) ABS solenoid relay power supply
31 -
32 -
33 -
34 (SP1) Speed signal output for speedometer
35 -
36 (IG1) IG1 power source input
37 (RR-) Rear wheel speed RH (-) signal input
38 - (Not used)
39 (RL+) Rear wheel speed LH (+) signal input
40 - (Not used)
41 - (Not used)
42 (STP) Stop light control relay input
43 (HZRI) Brake hold switch input
44 (STP2) Stop light switch input
45 -
46 (GND1) Skid control ECU ground

*: w/ Brake Pedal Load Sensing Switch



TERMINAL INSPECTION


a.
C360727C22
1.448,0.229 1.865,0.479 0.417,0.25 1.51,0.271 1.969,0.469 0.458,0.198 10 false A42 0.104,0.135 0.563,0.333 0.458,0.198 10 false *a
*a Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly))


Disconnect the connector and measure the voltage and resistance on the wire harness side.

HINT:

The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) because the connector is watertight.


Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A42-1 (+BM) - Body ground L - Body ground ABS motor relay power supply Always 11 to 14 V
A42-6 (CSW) - Body ground R - Body ground VSC OFF switch input VSC OFF switch ON → OFF (Pressed → not pressed) Below 1 Ω → 10 kΩ or higher
A42-10 (STPO) - Body ground R - Body ground Stop light control relay (stop light switch assembly) output Ignition switch ON 11 to 14 V
A42-14 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A42-17 (FSW+) - Body ground*1 GR - Body ground Brake pedal load sensing switch input Brake pedal load sensing switch OFF → ON (Brake pedal depressed → released) 950 to 1050 Ω → 203 to 223 Ω
A42-30 (+BS) - Body ground W - Body ground ABS solenoid relay power supply Always 11 to 14 V
A42-36 (IG1) - Body ground B - Body ground IG1 power source input Ignition switch ON 11 to 14 V
A42-42 (STP) - Body ground SB - Body ground Stop light control relay (stop light switch assembly) output Stop light switch ON → OFF (Brake pedal depressed → released) 11 to 14 V* → Below 1.5 V
A42-43 (HZRI) - Body ground B - Body ground Brake hold switch input Brake hold switch ON → OFF (Pressed → not pressed) Below 1 Ω → 10 kΩ or higher
A42-44 (STP2) - Body ground L - Body ground Stop light switch input Stop light switch assembly ON → OFF (Brake pedal depressed → released) 11 to 14 V* → Below 1.5 V
A42-46 (GND1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω

*: w/ Brake Pedal Load Sensing Switch


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.