Home › Engine / Hybrid System › 3ZR-FAE (FUEL) › FUEL TANK
RM32H0E _51 Engine / Hybrid System _060184 3ZR-FAE FUEL _0295036 FUEL TANK A

3ZR-FAE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77754B 1.INSTALL CHARCOAL CANISTER OUTLET HOSE

a.

Engage the 2 clamps to install the charcoal canister outlet hose to the fuel tank assembly.


Hide 77209F 2.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 3 clamps to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77026A 3.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Engage the 4 clamps to install the No. 1 fuel evaporation tube sub-assembly to the fuel tank assembly.


Hide 77651A 4.INSTALL NO. 1 FUEL TANK CUSHION

a.

Install the 2 new No. 1 fuel tank cushions to the fuel tank assembly.


Hide 77100 5.INSTALL FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.

Set the fuel tank assembly on an engine lifter.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.

Using the engine lifter, slowly raise the fuel tank assembly, and then install the fuel tank assembly with the 2 fuel tank band sub-assemblies with the 4 bolts.


c.
A393798N01
0.51,0.042 0.667,0.24 0.156,0.198 10 true 4 2.635,0.031 2.792,0.229 0.156,0.198 10 true 1 0.583,1.948 0.74,2.146 0.156,0.198 10 true 3 2.625,1.948 2.781,2.146 0.156,0.198 10 true 2

Tighten the 4 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77209F 6.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A396124

Connect the fuel tank main tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77026A 7.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A396125

Connect the No. 1 fuel evaporation tube sub-assembly to the fuel pipe and slide the clip to secure it.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77213E 8.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A393801C01
1.646,3.01 1.313,3.01 true 2.031,3.135 1.698,3.135 false 2.125,2.229 2.438,2.385 0.313,0.156 10 false *a 1.615,2.01 1.927,2.167 0.313,0.156 10 false *b 1.094,2.896 1.406,3.052 0.313,0.156 10 false *c 2.094,3.031 2.406,3.188 0.313,0.156 10 false *d
*a 120°
*b Up
*c Paint Mark (Fuel Tank To Filler Pipe Hose)
*d Protrusion (Fuel Tank Assembly)


Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the clamp to secure it.

HINT:

Make sure the clamp and fuel tank to filler pipe hose are positioned within the area shown in the illustration.



Hide 9.CONNECT FUEL TANK BREATHER TUBE

a.
A393793

Connect the fuel tank breather tube to the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77754B 10.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A397743C01
1.438,2.375 1.875,2.677 true 2.406,2.542 2.719,2.74 0.313,0.198 10 false *a 1.25,2.292 1.563,2.49 0.313,0.198 10 false *b
*a 120°
*b Paint Mark


Connect the charcoal canister outlet hose to the fuel tank filler pipe sub-assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the charcoal canister outlet hose clip at the correct angle.



Hide 77641A 11.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the fuel tank assembly with the nut and 4 clips.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 17430 12.INSTALL TAIL EXHAUST PIPE ASSEMBLY

Hide 77020A 13.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 14.ADD FUEL