Home › Engine / Hybrid System › 3ZR-FAE (EMISSION CONTROL) › EMISSION CONTROL SYSTEM
RM32H0E _51 Engine / Hybrid System _060194 3ZR-FAE EMISSION CONTROL _0295047 EMISSION CONTROL SYSTEM G

3ZR-FAE EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A345137

·

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.



PROCEDURE

Hide 1.INSPECT FUEL CUT OPERATION

CAUTION:
A345137

·

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.



a.

Start the engine.


b.

Warm up the engine.


c.

Increase the engine speed to at least 3500 rpm.


d.
A394533C01
0.792,0.917 1.125,0.917 true 0.948,1.51 1.281,1.51 true 0.75,1.417 1,1.583 0.25,0.167 10 true *1 0.594,0.823 0.833,1 0.24,0.177 10 true *a
*1 Fuel Injector Assembly
*a Sound Scope


Using a sound scope, check for injector operating sounds.


e.

When the accelerator pedal is released, check that injector operating sounds stop momentarily and then resume.

If the result is not as specified, check the injectors, wiring and ECM.

Standard:
Item Specified Condition
Fuel cut off engine speed 2700 rpm or higher
Fuel injection restart engine speed 1200 rpm



Hide 2.VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil dipstick, filler cap, ventilation hose or other components may cause the engine to run improperly.

·

Air suction caused by disconnections, looseness or cracks in any part of the air induction system between the throttle body assembly and cylinder head sub-assembly will cause engine failure or engine malfunctions.



If any defects are found, replace parts as necessary.


Hide 3.INSPECT EVAPORATIVE EMISSION CONTROL SYSTEM

CAUTION:
A345137

·

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.



a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Warm up the engine.


d.

Turn the GTS on.


e.
A394534

Slide the clip and disconnect the fuel vapor feed hose from the purge valve (purge VSV).


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

g.

Check that vacuum occurs at the purge valve (purge VSV) port.


h.

If vacuum does not occur, check the following items:

·

Purge valve (purge VSV)

·

Clogs in the fuel vapor feed hose that connects the intake manifold and purge valve (purge VSV)



i.

Exit Active Test mode and connect the fuel vapor feed hose and slide the clip to secure it.


j.

Enter the following menus: Powertrain / Engine and ECT / Data List / EVAP Purge VSV.

Powertrain > Engine and ECT > Data List
Tester Display
EVAP Purge VSV
50003 234 217

k.

Warm up the engine and drive the vehicle.


l.

Confirm that the purge valve (purge VSV) opens.

If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.