Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › CAMSHAFT OIL CONTROL SOLENOID
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0295064 CAMSHAFT OIL CONTROL SOLENOID G

8NR-FTS ENGINE CONTROL  CAMSHAFT OIL CONTROL SOLENOID  INSPECTION  


PROCEDURE

Hide 15370 1.INSPECT CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY

HINT:

Use the same procedure for the intake side and exhaust side.


a.

Check the resistance.

i.
A436352C01
0.122,0.095 0.323,0.262 0.201,0.167 10 *a
*a Component without harness connected
(Camshaft Timing Oil Control Solenoid Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 0 °C (32 °F) 5.3 to 6.3 Ω
20 °C (68 °F) 5.8 to 6.8 Ω
40 °C (104 °F) 6.2 to 7.4 Ω


If the result is not as specified, replace the camshaft timing oil control solenoid assembly.



b.

Stroke Amount Inspection

i.

Using vernier calipers, measure length (A) and (B) with the shaft of the camshaft timing oil control solenoid assembly set in the respective positions shown in the illustration.

A436354C01
0.167,0.115 3.156,2.656 2.99,2.542 3.458,0.115 6.448,2.656 2.99,2.542 1.406,1.063 1.802,1.063 false 4.719,1.104 5.115,1.104 false 1.458,1.729 1.635,1.729 1.635,1.729 1.823,1.948 false 4.75,1.729 4.927,1.729 4.927,1.729 5.115,1.948 false 0.604,0.323 0.917,0.479 0.313,0.156 10 false *a 0.625,2.073 0.938,2.229 0.313,0.156 10 false *b 1.219,0.99 1.531,1.146 0.313,0.156 10 false *c 4.542,1.031 4.854,1.188 0.313,0.156 10 false *c 2.375,0.969 2.688,1.125 0.313,0.156 10 false A 5.677,0.969 5.99,1.125 0.313,0.156 10 false A 2.406,1.938 2.771,2.229 0.365,0.292 10 false B 5.698,1.958 6.063,2.25 0.365,0.292 10 false B 3.917,0.302 4.229,0.458 0.313,0.156 10 false *a 3.927,2.125 4.24,2.281 0.313,0.156 10 false *b 0.229,0.167 0.604,0.406 0.375,0.24 12 false *A 3.521,0.167 3.896,0.406 0.375,0.24 12 false *B 4.563,1.667 4.875,1.823 0.313,0.156 10 false *c 1.281,1.667 1.594,1.823 0.313,0.156 10 false *c
*A Type A *B Type B
*a Shaft Side Facing Down *b Shaft Side Facing Up
*c Shaft - -


NOTICE:

Do not apply battery voltage to the terminals of the camshaft timing oil control solenoid assembly.


HINT:

If the shaft does not extend under its own weight, extend the shaft with your fingers.



ii.

Calculate the stroke amount based on the difference of length (A) and (B).

Standard:

6.5 mm (0.256 in.) or more


HINT:

Stroke amount = length (A) - length (B)


If the value is not as specified, replace the camshaft timing oil control solenoid assembly.