Home › Engine / Hybrid System › 8NR-FTS (STARTING) › STARTER (for Denso Made without Stop and Start System)
RM32H0E _51 Engine / Hybrid System _060199 8NR-FTS STARTING _0295162 STARTER(for Denso Made without Stop and Start System) A

8NR-FTS STARTING  STARTER(for Denso Made without Stop and Start System)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A324873

Using a 7 mm socket wrench, remove the 2 bolts.


b.
A324884C01
0.615,2.208 0.792,2.208 0.792,2.208 1.125,2.542 true 0.458,2.115 0.656,2.281 0.198,0.167 10 false *a
*a Terminal C


While lifting the rear of the magnet starter switch assembly disconnect it from terminal C.


c.
A324874C03
0.344,0.292 0.521,0.292 0.521,0.292 0.781,0.625 true 1.292,1.49 1.479,1.49 1.479,1.49 1.542,1.146 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *b 1.135,1.365 1.375,1.594 0.24,0.229 10 false *a
*a Hook
*b Pinion Drive Lever


While lifting the rear of the magnet starter switch assembly, remove the hook from the pinion drive lever, then remove the magnet starter switch assembly.


Hide 28120 2.REMOVE STARTER YOKE ASSEMBLY

a.
A324875

Using a 7 mm socket wrench, remove the 3 through bolts and pull out the starter yoke assembly together with the starter commutator end frame assembly.


Hide 3.REMOVE STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A248647C01
1.583,0.281 1.792,0.281 1.792,0.281 1.969,0.49 false 1.458,1.719 1.635,2.042 1.635,2.042 1.823,2.042 false 1.896,1.938 2.208,2.094 0.313,0.156 10 false *1 1.396,0.167 1.708,0.323 0.313,0.156 10 false *2
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly


Remove the starter commutator end frame assembly from the starter yoke assembly.


Hide 4.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A248649C09
0.875,1.385 1.177,1.385 1.177,1.385 1.646,1.854 true 1.01,0.667 1.583,0.667 false 0.646,2.115 1.219,2.115 false 2.167,2.969 2.74,2.969 false 0.479,2.01 0.792,2.167 0.313,0.156 10 false *1 2.813,2.854 3.125,3.01 0.313,0.156 10 false *2 0.708,1.292 1.021,1.448 0.313,0.156 10 false *3 0.844,0.552 1.156,0.708 0.313,0.156 10 false *a
*1 Starter Yoke Assembly
*2 Starter Brush Holder Assembly
*3 Starter Armature Assembly
*a Hammer


Remove the starter yoke assembly while holding down the starter armature assembly and starter brush holder assembly with the handle of a hammer.

HINT:

The starter armature assembly will be attracted by the magnetic field of the starter yoke assembly. Hold the starter armature assembly with the handle of the hammer.



Hide 28160 5.REMOVE STARTER ARMATURE ASSEMBLY

a.
A248650C01
0.354,0.438 0.542,0.438 0.542,0.438 0.781,0.719 false 1.896,1.458 2.156,1.875 2.156,1.875 2.375,1.875 false 2.448,1.76 2.76,1.917 0.313,0.156 10 false *1 0.146,0.323 0.458,0.479 0.313,0.156 10 false *2
*1 Starter Armature Assembly
*2 Starter Brush Holder Assembly


Remove the starter armature assembly from the starter brush holder assembly.


Hide 28021 6.REMOVE STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A324876

Remove the rubber seal from the starter drive housing assembly.


b.
A324877C01
2.521,1.104 2.604,0.885 2.604,0.885 2.833,0.885 false 1.146,1.875 1.146,1.542 false 2.875,0.781 3.188,0.938 0.313,0.156 10 false *1 1.083,1.896 1.396,2.052 0.313,0.156 10 false *2
*1 Starter Center Bearing Clutch Sub-assembly
*2 Starter Drive Housing Assembly


Remove the starter center bearing clutch sub-assembly from the starter drive housing assembly.


c.
A250735

Disengage the 3 claws and remove the starter shock absorber from the starter center bearing clutch sub-assembly.


d.
A248654

Remove the 3 planetary gears from the starter center bearing clutch sub-assembly.