Home › Engine / Hybrid System › 8NR-FTS (STARTING) › STARTER (for Denso Made with Stop and Start System) › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _060199 8NR-FTS STARTING _0295163 STARTER(for Denso Made with Stop and Start System) A

8NR-FTS STARTING  STARTER(for Denso Made with Stop and Start System)  DISASSEMBLY  


PROCEDURE

Hide 28150 1.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A355056

Remove the nut and disconnect the field coil lead wire from terminal C.


b.
A351866

While holding the magnet starter switch assembly to the starter drive housing assembly, remove the 2 nuts.


c.
A353484C02
1.594,0.115 1.719,0.115 1.719,0.115 1.792,0.281 false 0.333,0.198 0.458,0.198 0.458,0.198 0.865,0.469 true 1.406,0.021 1.719,0.177 0.313,0.156 10 false *a 0.167,0.115 0.479,0.271 0.313,0.156 10 false *b
*a Hook
*b Pinion Drive Lever


While lifting the rear of the magnet starter switch assembly, remove the hook from the pinion drive lever, then remove the magnet starter switch assembly.


Hide 28120 2.REMOVE STARTER YOKE ASSEMBLY

a.
A351867C02
1.01,2 1.219,2 1.219,2 1.396,1.74 false 2.813,1.073 2.938,0.854 2.938,0.854 3.115,0.854 false 0.844,1.927 1.156,2.083 0.313,0.156 10 false *1 3.167,0.76 3.385,0.979 0.219,0.219 10 false *a
*1 Starter Yoke Assembly
*a Starter Commutator End Frame Assembly


Using a T25 "TORX" socket wrench, remove the 2 through bolts, and pull out the starter yoke assembly together with the starter commutator end frame assembly.


Hide 3.REMOVE STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A187214C03
2.198,0.49 2.625,0.49 false 0.635,1.792 0.865,1.792 0.865,1.792 0.938,1.49 false 2.344,1.375 2.771,1.375 false 2.677,0.375 2.99,0.531 0.313,0.156 10 false *a 2.823,1.24 3.135,1.438 0.313,0.198 10 false *1 0.427,1.688 0.74,1.885 0.313,0.198 10 false *2
*1 Starter Commutator End Frame Assembly
*2 Starter Yoke Assembly
*a Field Coil Lead Wire


Remove the 2 screws.


b.

While holding down the field coil lead wire, remove the starter commutator end frame assembly from the starter yoke assembly.


Hide 28140 4.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A064784C06
1.073,0.208 1.313,0.208 1.313,0.208 1.552,0.51 false 1.948,0.563 2.167,0.219 2.167,0.219 2.396,0.219 false 2.458,0.094 2.771,0.25 0.313,0.156 10 false *a 0.885,0.104 1.198,0.26 0.313,0.156 10 false *b
*a Brush Spring
*b Brush


Using a screwdriver, hold the brush spring back and disconnect the 4 brushes.


b.

Remove the starter brush holder assembly from the starter armature assembly.


Hide 28160 5.REMOVE STARTER ARMATURE ASSEMBLY

a.
A202438C01
1.49,0.406 1.938,0.229 1.938,0.229 2.188,0.229 false 1.615,1.958 1.823,1.958 1.823,1.958 2.073,1.635 false 2.229,0.135 2.542,0.333 0.313,0.198 10 false *1 1.417,1.885 1.729,2.083 0.313,0.198 10 false *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Remove the starter armature assembly from the starter yoke assembly.


Hide 6.REMOVE STARTER ARMATURE PLATE

a.
A351869C02
2.156,0.583 2.344,0.583 2.344,0.583 2.5,0.802 false 0.24,0.667 0.448,0.667 false 0.99,1.844 1.167,2 1.167,2 1.365,2 false 1.854,1.771 2.073,1.771 2.073,1.771 2.24,1.469 false 2.01,0.5 2.323,0.656 0.313,0.156 10 false *1 0.094,0.573 0.406,0.729 0.313,0.156 10 false *2 1.688,1.688 2,1.844 0.313,0.156 10 false *a 1.427,1.917 1.74,2.073 0.313,0.156 10 false *a
*1 Starter Yoke Assembly
*2 Starter Drive Housing Assembly
*a Starter Armature Plate


Remove the starter armature plate from the starter drive housing assembly or starter yoke assembly.


Hide 7.REMOVE PLANETARY GEAR

a.
A351870

Remove the 3 planetary gears from the starter drive housing assembly.


Hide 28021 8.REMOVE STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A351871C02
0.281,1.219 0.563,1.219 false 1.74,0.271 2.021,0.271 false 2.802,0.583 2.927,0.323 2.927,0.323 3.073,0.323 false 1.74,1.833 2.021,1.833 false 1.594,1.771 1.906,1.927 0.313,0.156 10 false *1 0.115,1.156 0.427,1.313 0.313,0.156 10 false *2 1.594,0.188 1.813,0.385 0.219,0.198 10 false *a 3.115,0.24 3.427,0.396 0.313,0.156 10 false *b
*1 Starter Center Bearing Clutch Sub-assembly
*2 Starter Drive Housing Assembly
*a Pinion Drive Lever
*b Rubber Seal


Remove the starter center bearing clutch sub-assembly together with the pinion drive lever and rubber seal from the starter drive housing assembly.


b.

Remove the pinion drive lever and rubber seal from the starter center bearing clutch sub-assembly.