Home › Power Source / Network › 8NR-FTS (BATTERY / CHARGING) › GENERATOR (for DENSO Made)
RM32H0E _57 Power Source / Network _060209 8NR-FTS BATTERY / CHARGING _0295252 GENERATOR(for DENSO Made) A

8NR-FTS BATTERY / CHARGING  GENERATOR(for DENSO Made)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE GENERATOR PULLEY CAP

a.
A351883

Remove the generator pulley cap from the generator pulley with clutch.

NOTICE:

Do not reuse the generator pulley cap.



Hide 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
A351884C02
1.573,0.302 1.813,0.302 1.813,0.302 2.073,0.698 false 3.01,1.698 3.01,1.063 false 2.521,2.25 2.219,2.25 false 1.406,0.219 1.719,0.375 0.313,0.156 10 false *a 2.865,1.771 3.313,2 0.448,0.229 10 false SST A 2.573,2.177 3.021,2.406 0.448,0.229 10 false SST A
*a Rotor Shaft


Fit the rotor shaft end into SST (A).

SST
09820-70010  (09821-70010, 09822-70010)


c.
A351885C02
2.833,1.719 2.833,1.031 false 2.25,2.479 2.094,2.479 2.094,2.479 2.021,2.271 false 1.583,0.406 2.052,0.406 false 1.427,0.333 1.74,0.49 0.313,0.156 10 false *1 2.698,1.771 3.208,2 0.51,0.229 10 false SST B 2.313,2.417 2.823,2.646 0.51,0.229 10 false SST B
*1 Generator Pulley with Clutch


Fit SST (B) to the generator pulley with clutch.

NOTICE:

Securely attach SST to the generator pulley with clutch and rotor shaft.



d.
A351886C02
0.813,1.875 1.26,1.875 false 2.198,1.448 2.604,1.74 2.604,1.74 2.896,1.74 true 2.271,1.063 2.406,0.917 2.406,0.917 2.563,0.917 false 2.115,0.979 2.26,0.719 2.26,0.719 2.406,0.719 true 2.958,1.656 3.271,1.813 0.313,0.156 10 false *a 0.635,1.792 0.948,1.948 0.313,0.156 10 false *b 2.625,0.844 3.125,1.01 0.5,0.167 10 false SST A 2.448,0.656 2.948,0.823 0.5,0.167 10 false SST B
*a Turn
*b Hold


Loosen the generator pulley with clutch by turning SST (A) as shown in the illustration.

NOTICE:
·

Check that the generator assembly is secured in the vise tightly.

·

Hold SST tightly during the operation.




e.

Remove SST (A) and (B) from the generator pulley with clutch.


f.

Remove the generator pulley with clutch from the rotor shaft.


g.

Remove the generator assembly from the vise.


Hide 3.REMOVE GENERATOR REAR END COVER

a.

Place the generator assembly on the generator pulley with clutch.


b.
A330283

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 4.REMOVE GENERATOR TERMINAL INSULATOR

a.
A330284

Remove the generator terminal insulator from the generator coil assembly.


Hide 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A330285

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A330286

Remove the 4 bolts.


b.
A392476C01
2.073,0.823 2.406,0.823 false 0.656,1.594 1.073,1.594 true 0.604,0.583 0.917,0.74 0.313,0.156 10 false *a 2.75,0.063 3.063,0.219 0.313,0.156 10 false *b 2.469,0.75 2.865,0.917 0.396,0.167 10 false SST 1.135,1.531 1.531,1.698 0.396,0.167 10 false SST
*a Hold
*b Turn


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


c.
A392477

Remove the bearing cover packing.

NOTICE:

If the bearing cover packing breaks, remove the broken pieces completely.


HINT:

The bearing cover packing may be installed on the generator rotor assembly.



Hide 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A392478

Remove the generator rotor assembly.

NOTICE:

Do not drop the generator rotor assembly.



Hide 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A392479

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A392480E01
1.156,1.354 2.052,1.781 true 1.156,1.208 2.042,1.771 true 2.083,1.708 2.542,1.906 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)