Home › Power Source / Network › 3ZR-FAE (BATTERY / CHARGING) › GENERATOR
RM32H0E _57 Power Source / Network _060210 3ZR-FAE BATTERY / CHARGING _0295253 GENERATOR A

3ZR-FAE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE GENERATOR PULLEY CAP

a.
A287135

Using a screwdriver, remove the generator pulley cap from the generator pulley with clutch.

NOTICE:

Do not reuse the generator pulley cap.



Hide 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.
A284135N02
1.354,0.646 1.052,0.354 1.052,0.354 0.813,0.354 false 2.344,0.875 2.073,0.875 2.073,0.875 1.76,1.417 false 0.375,0.292 0.958,0.542 0.583,0.25 10 false SST A 2.438,0.792 2.99,1.063 0.552,0.271 10 false SST B

Confirm SST (A) and (B) shown in the illustration.

SST
09820-63021  


c.
A204355C09
2.948,0.885 2.948,1.458 false 2.094,0.563 1.844,0.188 1.844,0.188 1.615,0.188 false 1.625,1.01 1.896,1.76 1.896,1.76 2.125,1.76 true 1.406,0.094 1.635,0.25 0.229,0.156 10 false *a 2.75,1.521 3.219,1.729 0.469,0.208 10 false SST A 2.208,1.688 2.646,1.865 0.438,0.177 10 true SST A
*a Rotor Shaft


Place the rotor shaft end into SST (A).


d.
A214792C05
2.896,0.115 2.781,0.115 2.781,0.115 2.51,0.302 false 1.49,0.146 1.667,0.146 1.667,0.146 1.99,0.25 false 1.479,1.01 1.906,1.344 1.906,1.344 2.135,1.344 false 2.938,0.042 3.396,0.219 0.458,0.177 10 false SST B 2.198,1.25 2.688,1.448 0.49,0.198 10 false SST B 1.281,0.073 1.542,0.281 0.26,0.208 10 false *1
*1 Generator Pulley with Clutch


Fit SST (B) to the generator pulley with clutch.


e.
A204356C08
2.146,0.771 2.302,0.531 2.302,0.531 2.479,0.531 false 1.896,0.563 2.094,0.156 2.094,0.156 2.313,0.156 false 1.385,1.875 1.156,1.875 false 2.542,0.448 3.135,0.719 0.594,0.271 10 false SST A 2.365,0.083 2.958,0.344 0.594,0.26 10 false SST B 1.802,1.865 1.969,2.021 0.167,0.156 10 false *b 0.958,1.781 1.125,1.938 0.167,0.156 10 false *a
*a Turn
*b Hold


Loosen the generator pulley with clutch by turning SST (B) as shown in the illustration.

NOTICE:
·

Check that the generator drive end frame is secured in the vise tightly.


·

Hold SST (A) tightly during the operation.




f.

Remove SST from the generator pulley with clutch.


g.

Remove the generator pulley with clutch from the rotor shaft.


h.

Remove the generator assembly from the vise.


Hide 3.REMOVE GENERATOR REAR END COVER

a.
A153378

Place the generator assembly on the generator pulley with clutch.


b.
A330875

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 4.REMOVE GENERATOR TERMINAL INSULATOR

a.
A330876

Remove the generator terminal insulator from the generator coil assembly.


Hide 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A330877

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A330878

Remove the 4 bolts.


b.
A153383C18
1.063,1.802 0.99,1.802 0.99,1.802 0.635,1.573 false 2.667,0.688 2.563,0.688 2.563,0.688 2.094,0.854 false 1.115,1.719 1.406,1.875 0.292,0.156 10 false SST 2.719,0.604 3.01,0.75 0.292,0.146 10 false SST 2.823,0.094 3.135,0.25 0.313,0.156 10 false *a 0.615,0.563 0.927,0.719 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010)


c.
A284548

Remove the bearing cover packing.

NOTICE:

If the bearing cover packing breaks, remove the broken pieces completely.


HINT:

The bearing cover packing may be installed on the generator rotor assembly.



Hide 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A118367C02
0.646,0.375 0.979,0.375 0.979,0.375 1.208,0.74 false 2.365,1.604 2.604,1.844 2.604,1.844 2.844,1.844 false 0.438,0.313 0.75,0.469 0.313,0.156 10 false *1 2.896,1.74 3.208,1.896 0.313,0.156 10 false *2
*1 Generator Rotor Assembly
*2 Generator Drive End Frame


Remove the generator rotor assembly from the generator drive end frame.


Hide 8.INSPECT GENERATOR DRIVE END FRAME BEARING

Hide 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A153385

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A264634N01
1.946,1.566 2.25,1.727 0.304,0.161 10 SST 1.912,1.647 1.213,1.354 false 1.912,1.647 1.204,1.136 false

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)