Home › Power Source / Network › 3ZR-FAE (BATTERY / CHARGING) › GENERATOR
RM32H0E _57 Power Source / Network _060210 3ZR-FAE BATTERY / CHARGING _0295253 GENERATOR A

3ZR-FAE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A183132N04
1.073,0.677 0.531,0.281 0.531,0.281 0.948,1.042 false 2.354,0.677 1.865,0.323 1.865,0.323 2.156,0.833 false 0.219,0.198 0.583,0.365 0.365,0.167 10 SST 1.573,0.24 1.958,0.427 0.385,0.188 10 SST

Using SST and a press, install a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A153389C11
2.729,1.344 2.448,2 2.448,2 2.208,2 true 2.74,0.865 2.031,0.302 2.031,0.302 1.813,0.302 false 1.615,0.219 1.781,0.365 0.167,0.146 10 false *a 2.042,1.906 2.208,2.063 0.167,0.156 10 false *b
*a Tab
*b Cutout


Fit the tabs of the retainer plate into the cutouts of the generator drive end frame to install the retainer plate.


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A118367C06
1.24,0.74 0.854,0.417 false 2.365,1.604 2.833,1.833 false 0.656,0.313 0.969,0.469 0.313,0.156 10 false *1 2.906,1.729 3.219,1.885 0.313,0.156 10 false *2
*1 Generator Rotor Assembly
*2 Generator Drive End Frame


Place the generator drive end frame on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame.


Hide 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A314531C01
1.938,0.5 2.448,0.5 true 1.927,1.448 2.438,1.448 true 2.49,0.417 2.802,0.573 0.313,0.156 10 false *a 2.479,1.385 2.792,1.542 0.313,0.156 10 false *b
*a Protrusion
*b Groove


Install a new bearing cover packing.

NOTICE:

Align the protrusions of the bearing cover packing with the grooves of the generator coil assembly when installing.



b.
A285303N03
2.635,0.563 2.792,0.177 2.792,0.177 2.969,0.177 false 1.188,0.688 0.844,0.24 0.844,0.24 0.594,0.24 false 3.031,0.083 3.406,0.313 0.375,0.229 10 false SST 0.292,0.146 0.729,0.344 0.438,0.198 10 false SST

Using SST and a press, slowly press the generator coil assembly to install it.

SST
09612-70100  (09612-07240)


c.

Install the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A153827C12
2.479,0.74 1.979,0.198 1.979,0.198 1.729,0.198 false 0.917,0.521 0.708,0.198 0.708,0.198 0.458,0.198 false 1.521,0.094 1.833,0.313 0.313,0.219 10 false *a 0.271,0.104 0.583,0.323 0.313,0.219 10 false *a
*a Pin (1.0 mm)


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.


b.
A284142C02
1.76,1.042 2.646,1.656 2.646,1.656 2.854,1.656 false 2.917,1.604 3.229,1.76 0.313,0.156 10 false *a
*a Pin (1.0 mm)


Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly hole.


Hide 5.INSTALL GENERATOR TERMINAL INSULATOR

a.

Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Be sure to install the generator terminal insulator in the correct direction.



Hide 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 7.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.

Temporarily install the generator pulley with clutch to the rotor shaft.


c.
A284135N03
1.354,0.646 1.052,0.354 1.052,0.354 0.813,0.354 false 2.344,0.875 2.073,0.875 2.073,0.875 1.76,1.417 false 0.375,0.292 0.958,0.542 0.583,0.25 10 false SST A 2.438,0.792 2.99,1.063 0.552,0.271 10 false SST B

Confirm SST (A) and (B) shown in the illustration.

SST
09820-63021  


d.
A204357C12
1.25,0.604 1.542,0.188 1.542,0.188 1.792,0.188 false 1.552,1.281 1.552,1.063 false 0.313,0.927 0.313,1.615 false 1.854,0.104 2.146,0.281 0.292,0.177 10 false *a 1.385,1.302 1.823,1.49 0.438,0.188 10 true SST A 0.115,1.677 0.677,1.906 0.563,0.229 10 false SST A
*a Rotor Shaft


Place the rotor shaft end into SST (A).


e.
A214793C05
1.563,0.76 1.458,0.135 1.458,0.135 1.292,0.135 false 0.375,0.938 0.375,1.458 true 0.844,1.01 0.844,1.531 true 0.833,0.052 1.344,0.219 0.51,0.167 10 false SST B 0.208,1.51 0.677,1.677 0.469,0.167 10 false SST B 0.75,1.573 1.031,1.729 0.281,0.156 10 true *1
*1 Generator Pulley with Clutch


Fit SST (B) to the generator pulley with clutch.


f.
A229066C06
0.823,1.219 0.698,1.563 0.698,1.563 0.521,1.563 false 1.125,0.885 0.771,0.667 0.771,0.667 0.552,0.667 false 0.094,0.604 0.625,0.979 0.531,0.375 10 false SST B 0.063,1.49 0.583,1.865 0.521,0.375 10 false SST A 0.927,2.677 1.115,2.844 0.188,0.167 10 false *a 2.313,0.979 2.5,1.146 0.188,0.167 10 false *b 1.375,4.104 1.563,4.271 0.188,0.167 10 false *c 1.948,2.292 2.135,2.458 0.188,0.167 10 false *d
*a Hold
*b Torque Wrench Fulcrum Length
*c SST Fulcrum Length
V100135

Turn


Tighten the generator pulley with clutch by turning SST (B) as shown in the illustration.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:

Be careful as the generator pulley with clutch or rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (15.7 in.)): 64 N*m (653 kgf*cm, 47 ft.*lbf)




g.

Remove SST from the generator pulley with clutch.


h.

Check that the generator pulley with clutch rotates smoothly.


i.

Remove the generator drive end frame from the vise.


Hide 8.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.