STOP AND START CONTROL
The stop and start system operates according to the following conditions, achieving appropriate engine stop and start control together with safe and smooth driving characteristics.
When all of the conditions in the following table have been met, the engine is stopped by stop and start control.
| Item | Condition
(All of the following conditions are met) |
|
|---|---|---|
| Idle Stop | Ignition Switch | 5 seconds or more have passed with the ignition switch ON |
| Engine Coolant Temperature | 40 to 105°C (104 to 221°F) | |
| Ambient Temperature | Higher than -5°C (23°F) | |
| Driver Door | 3 seconds have elapsed after driver door closed | |
| Driver Seat Belt | 3 seconds have elapsed after driver seat belt fastened | |
| Vehicle Stability Control System | Normal | |
| Brake Booster Vacuum | Sufficient (In a level area, 42.5 kPa (0.43 kg/cm2, 6.1 psi) or higher) | |
| Shift Position | Shift lever is in neutral | |
| Stop and Start System Cancel Switch | Off (System control is not prohibited) | |
| Vehicle Speed | 0 km/h (0 mph) (After the engine warms up) | |
| Engine Speed | Below 1250 rpm | |
| Engine Hood | 3 seconds have elapsed after hood closed | |
| Battery Voltage | When using specified battery:
6.50 V or higher when starter begins operation and 6.50 V or higher when cranking When using non-specified battery:
8.92 V or higher when starter begins operation and 8.92 V or higher when cranking |
|
| Battery Temperature*1 | -10°C or higher and 70°C or less (14°F or higher and 158°F or less) | |
| Battery Integrated Current*2 | One of the following conditions is met:
·
-4554 A-sec or more: "Status of Battery Charge Control"*3 is Charge Control Coordination Mode or Stop and Start Standalone Mode or Low Temperature Mode ·
0 A-sec or more: "Status of Battery Charge Control"*3 is Stop and Start Restriction Mode or Temperature High/Low Mode |
|
| Air Conditioning | Other than when stop and start control is prohibited | |
| Heater | One of the following conditions is met:
·
Blower switch is off ·
Blower switch is on when the ambient temperature is higher than 10°C (50°F), the engine coolant temperature is higher than 55°C (131°F) or the room temperature is 5°C (41°F) lower than the set temperature ·
Blower switch on, air conditioning switch off and a certain amount of time has elapsed after engine restarted by stop and start control |
|
| Steering Operation | 45 deg/s or less | |
| Engine Control | Engine catalytic rapid warm-up is completed | |
*1: When the battery temperature is below -15°C (5°F) or less, or 75°C (167°F) or higher, stop and start control is prohibited. When the battery temperature returns to -10°C (14°F) or higher, and 70°C (158°F) or less, stop and start control is permitted.
*2: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST
*3: Refer to the Data List "Status of Battery Charge Control" for information about the status of the battery charge control.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST
When the engine is stopped by stop and start control, and any of the following conditions are met, the engine will restart.
| Item | Condition
(Any of the following conditions is met) |
|
|---|---|---|
| Engine Restart | Brake Booster Vacuum | Brake booster vacuum insufficient (Under 37.5 kPa (0.38 kg/cm2, 5.4 psi)) |
| Engine Hood Courtesy Switch (Hood Lock Assembly) | ·
When hood lock assembly (hood courtesy switch) was opened (shift lever is only in neutral) ·
Hood lock assembly (hood courtesy switch) malfunctioning |
|
| SFI System | Malfunction in SFI system is detected | |
| Power Steering System | Malfunction in power steering system is detected | |
| Air Conditioning | Timer in the air conditioning amplifier assembly runs out | |
| Heater | Timer in the air conditioning amplifier assembly runs out | |
| Air Conditioning/Heater | Both of the following conditions are met:
·
Blower switch: ON ·
Evaporator temperature exceeds threshold value (threshold value varies with temperature, humidity and amount of solar radiation) Any of the following conditions are met:
·
A/C switch, blower switch: ON ·
Front defogger switch: ON ·
Blower switch turned off during auto control or blower mode changed to manual ·
Changes stop and start system priority control from "priority (Extended)"to "normal (standard)" |
|
| Battery | Battery voltage drops (11.4 V or less) | |
| Battery Integrated Current* | The accumulated value of discharge current during engine stop is too large (5940 A-sec or more) | |
| Vehicle Speed | Vehicle speed signal is input (Vehicle stopped on a slope, etc.) | |
| Driver Door | Open | |
| Driver Seat Belt | Driver seat belt is unfastened | |
| Steering Wheel | Steering wheel turned 25 deg or more | |
| Accelerator Pedal | Accelerator pedal is depressed | |
| Stop and Start System Cancel Switch | When stop and start system cancel assembly switch turn from off to on | |
| Clutch pedal | Clutch pedal is depressed | |
*: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST
SYSTEM PROHIBITION CONTROL
The engine stop and start ECU prohibits stop and start control by the stop and start system according to the table below. The prohibition conditions are specified for each system.
| System | Prohibition Condition | Vehicle State | Restoration Condition | Prohibition Condition Check Timing |
|---|---|---|---|---|
| Engine | Engine coolant temperature less than 40°C (104°F) | Engine has not warmed up | Engine coolant temperature 40 between 105°C (104 to 221°F) | Always |
| Idle speed learning has not completed | Stop and start control prohibited until idle speed learning completes | Idle speed learning has completed | Always | |
| Engine catalytic rapid warm-up | Engine catalytic rapid warm-up is being performed | Engine catalytic rapid warm-up is completed | Each time engine is started or vehicle is stopped | |
| Brake | Brake booster vacuum decreases | Brake booster vacuum decreases due to pumping the brakes, etc. | Normal brake booster vacuum is reached | Every time the vehicle stops |
| Air Conditioning | Heater:
When blower switch is on and ambient temperature 10°C (50°F) or less, any of the following conditions are met:
·
Engine coolant temperature 45°C (113°F) or less ·
Cabin temperature lower than set temperature by 11 °C (19.8 °F) or higher (only when stop and start system priority control is set to "Normal (Standard)" mode) |
Heater performance decreases | ·
Actual temperature higher than target temperature ·
Blower switch off |
While the heater is on |
| Cooling function:
When blower switch and A/C switch are on and ambient temperature 23°C (73.4°F) or higher, the following condition is met:
·
Evaporator temperature 9°C (48.2°F) or higher ·
Cabin temperature higher than set temperature by 2 °C (3.6 °F) or higher, or blower level 16 or higher (only when stop and start system priority control is set to "Normal (Standard)" mode) |
Cooling performance decreases | Any of the following conditions have been met:
·
Actual temperature higher than target temperature ·
Blower switch is off ·
A/C switch is off |
While the air conditioning system (cooling function) is on | |
| Defogger:
All of the following conditions are met:
·
Defogger switch on ·
Blower switch on |
Fogging of windows | Defogger switch or blower switch off | Always | |
| Temporary start and start control:
Both of the following conditions are met:
·
Blower switch on ·
Evaporator temperature exceeds threshold (threshold varies with temperature, humidity and amount of solar radiation) ·
Within the certain period after restarting from idling stop (threshold value varies depending on the operating condition of idling stop) |
Blower switch on | Blower switch off and evaporator temperature within specified range | Always | |
| Driver Door | Driver door opened before engine stop by engine stop and start control | Driver door courtesy switch ON signal input | 3 seconds have elapsed since driver door was closed | Always |
| Engine Hood | Engine hood opened before engine stop by stop and start control | Engine hood courtesy switch (hood lock assembly) OFF signal is input | 3 seconds have passed since engine hood was closed | Always |
| Seat Belt | Driver seat belt not fastened before engine stop by engine stop and start control | Driver seat belt buckle switch OFF signal input | 3 seconds have passed since driver seat belt was fastened | Always |
| Steering Wheel | Steering wheel turned at a speed of 45 deg/s or more | Steering wheel operation signal input | Steering wheel being held | Always |
| Shift Position | Shift lever is in position other than neutral | Shift position signal input | Shift lever is in neutral | Always |
| Ambient Temperature | Ambient temperature lower than -5 °C (23.0 °F) | - | Ambient temperature -5°C (23°F) or higher | Always |
| Power Source | When using specified battery:
Below 6.50 V when starter begins operation and below 6.50 V when cranking When not using specified battery:
Below 8.92 V when starter begins operation and below 8.92 V when cranking |
Battery charge insufficient or battery has deteriorated | Battery charged or replaced | Every time the engine is started |
| Battery temperature -15°C (5°F) or less, or 75°C (167°F) or higher | Depends on environmental temperature | Temperature is reached (-10°C (14°F) or higher and 70°C (158°F) or less | Always | |
Battery integrated current*1 value meets one of the following conditions:
·
-5544 A-sec or less: "Status of Battery Charge Control"*2 is Charge Control Coordination Mode or Stop and Start Standalone Mode or Low Temperature Mode ·
-990 A-sec or less: "Status of Battery Charge Control"*2 is Stop and Start Restriction Mode or Temperature High/Low Mode |
·
Heavy electrical load ·
High stop and start rate (Time that engine stopped by stop and start control is long) |
Battery integrated current*1 value meets both of the following conditions:
·
-4554 A-sec or higher: "Status of Battery Charge Control"*2 is Charge Control Coordination Mode or Stop and Start Standalone Mode or Low Temperature Mode ·
0 A-sec or higher: "Status of Battery Charge Control"*2 is Stop and Start Restriction Mode or Temperature High/Low Mode |
Always | |
| During refresh charge | ·
Cable reconnected to battery terminal ·
Refresh charge is performed for 30 minutes or longer for every 30 hours of driving |
·
Cable reconnected to battery terminal: 5 to 60 minutes ·
Periodic refresh charge: 30 to 60 minutes |
Always | |
| Engine started with the engine hood open | - | After ignition switch is turned off, ignition switch is turned to ON with hood closed | Every time the engine is started | |
| Idling Stop Rate | Idling stop rate for one trip is more than 50% or total idling stop rate is more than 40% | Vehicle is frequently stopped | Idling stop rate has decreased due to vehicle being driven and engine idling | Always |
*1: Read the Data List item "Integrated Current" or "Oper Permission (Integrated Current)" when checking the integrated current value.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST
*2: Please refer to the Data List "Status of Battery Charge Control" for information about the status of the battery charge control.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
When the engine stalled, in a state of stop and start system operation conditions have been met, the engine can restart by pressing the clutch pedal immediately (within 5 seconds or less from the engine stalled).
WARNING CONTROL
If any of the following operations are performed while the engine is stopped due to stop and start control, the system will not restart the engine. The engine will change the mode from "stopped due to system control" to "stalled" or the driver will be warned using the buzzer.
| Operation | Warning Control |
|---|---|
| The engine hood is opened | The engine stops (mode changes to "stalled", and the engine cannot be restarted until the ignition switch is turned off and then to ON) |
| The driver door is opened with the shift lever in neutral | The engine starts |
| The driver seat belt is unfastened | The engine starts |
| The shift lever is operated without depressing the clutch pedal | The buzzer sounds and stop and start indicator light blinks (engine will not start) |
WARNING INDICATOR AND BUZZER OPERATION
| *a | Stop and Start Indicator Light |
| *b | Stop and Start Cancel Indicator Light |
The driver is informed of the system control status and warnings by the stop and start indicator light, stop and start cancel indicator light and the buzzer.
| Item | Condition | Stop and start indicator light | Stop and start cancel indicator light | Buzzer |
|---|---|---|---|---|
| For 3 seconds after the ignition switch ON | Normal operation | Comes on | Comes on | Does not sound |
| During stop and start control operation (engine is stopped) | Normal operation | Comes on | Does not come on | Does not sound |
| The shift lever is operated without depressing the clutch pedal | The blinking interval 0.15 seconds | Does not come on | Sounds | |
| Control is prohibited by the stop and start system cancel switch (electric parking brake switch assembly) | Normal operation | Does not come on | Comes on | Does not sound |
| Diagnostic trouble code | Any DTCs are stored | Does not come on | Blinks at 0.5 second intervals. | Does not sound |
| Starter assembly life | Number of times the starter has been operated exceeds its limit | Does not come on | Blinks at 0.5 second intervals. | Does not sound |
STOP AND START SYSTEM OPERATION CONDITION DISPLAY FUNCTION
The stop and start system operation condition is displayed on the multi-information display.
| Stop and Start System Condition | Multi-information Display Message*2 | Vehicle Condition | |
|---|---|---|---|
| When the engine cannot be stopped by the stop and start system |
*1 |
"For Climate Control" | ·
The air conditioning system is being used when the ambient temperature is high or low. ·
Windshield defogger is pressed. |
| "Battery Charging" | ·
The battery charge amount may be low. ·
A refresh charge may be occurring. |
||
| "For Brake System" | ·
The vehicle is being driven in a high altitude area. ·
The brake booster vacuum is low. |
||
| "Driver Seat Belt Unbuckled" | The driver seat belt is not fastened. | ||
| "Non-Dedicated Battery" | A non-specified battery for the stop and start system may have been installed. | ||
| When the engine automatically restarts while stopped by the stop and start system |
*1 |
"Hood open" | The hood has been opened. |
| "Stop & Start Unavailable" | The engine may have been started with the hood opened. | ||
| "System Temp Low" | The battery may be cold. | ||
| "System Temp High" | The battery may be extremeiy hotd. | ||
| "Driver Seat Belt Unbuckled" | The driver seat belt is not fastened. | ||
| "Steering Wheel Turned" | The steering wheel is turned. | ||
| "For Brake System" | The brake pedal has been depressed futher or pumped. | ||
| "For Climate Control" | ·
The air conditioning system is turned on or the air conditioning is being used. ·
Windshield defogger is turned on. |
||
| "Battery Charging" | The battery charge amount may be low. | ||
| When the engine cannot be restarted by the stop and start system | - | "Stop & Start System active. Shift to N and depress clutch to restart" | The shift lever has been shifted from neutral to another position with the clutch pedal released. |
| Stop and start system may be malfunctioning | - | "Stop & Start System Malfunction"
"Visit Your Dealer" |
- |
*1: When the engine cannot be stopped by the stop and start system or the engine is restarted while the engine is stopped by the stop and start system, the following mark is displayed on the multi-information display.
*2: Examples of messages displayed during different situations are listed below in order of priority (some messages may not be displayed depending on the vehicle).
Engine cannot be stopped by stop and start system
"Non-Dedicated Battery", "Battery Charging", "For Brake System", "For Climate Control", "Driver Seat Belt Unbuckled", "Depress Brake Firmly to Activate"
Engine automatically restarted while engine stopped by stop and start system
"Driver Seat Belt Unbuckled", "Steering Wheel Turned", "For Brake System", "For Climate Control", "Battery Charging"
STOP AND START SYSTEM OPERATION
Depending on the type of malfunction, stop and start control may be prohibited by the fail-safe function. The following table shows effects on the vehicle and areas to be inspected when there is a malfunctions in the stop and start system.
| Malfunctioning Area | Malfunction | DTC Output | Data List / Freeze Frame Data | Effect on Vehicle | Area to be Inspected |
|---|---|---|---|---|---|
| IGSW circuit | Open | P2531 | ·
IG Switch ·
IG SW Abnoml |
Stop and start control prohibited | Wire harness or connector |
| +B circuit | Open | - | Data List cannot be checked because power not supplied to the engine stop and start ECU | Stop and start control prohibited | Wire harness or connector |
| TMN (neutral position switch) circuit | Open | P1780 | ·
Neutral Switch ·
N position Switch ·
N Position Voltage Status |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Neutral position switch |
| Shorted | P1780 | ·
Neutral Switch ·
N position Switch ·
N Position Voltage Status |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
||
| CLL (clutch start switch assembly) circuit | Stuck on | P0831 | ·
Clutch Lower SW ·
Clutch Lower SW Stuck ON ·
N/Clutch Lower SW Abnoml (ON) |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Clutch start switch assembly |
| Stuck off | - | ·
Clutch Lower SW ·
Clutch Lower SW Stuck OFF ·
N/Clutch Lower SW Abnoml (OFF) |
Stop and start control prohibited | ||
| BNT1 (engine hood courtesy switch) circuit | Stuck on | - | Hood Courtesy Switch | The engine does not stall when the engine hood is opened with the shift lever in neutral while the engine is stopped by stop and start control | ·
Wire harness or connector ·
Engine hood courtesy switch (Hood lock assembly) |
| Stuck off | - | Hood Courtesy Switch | Stop and start control prohibited despite engine hood being closed | ||
| BRVC/PB/BRE2 (vacuum sensor) circuit | Open | P1540 | ·
Brk Boost Sen Abnoml 1 ·
Brk Boost Sen Abnoml 2 ·
Brk Boost Sen Abnoml 3 |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Vacuum sensor assembly ·
Brake booster assembly ·
Vacuum hose (brake booster hose) |
| Shorted | P1540 | ||||
| Remains at intermediate value | P1541 | ||||
| ECAN (stop and start system cancel switch (electric parking brake switch assembly)) circuit | Stuck on | - | Cancel Switch | Stop and start control prohibited | ·
Wire harness or connector ·
Stop and start system cancel switch (electric parking brake switch assembly) |
| Stuck off | - | Cancel Switch | Stop and start control cannot be canceled by pressing the stop and start system cancel switch (electric parking brake switch assembly) | ||
| STA circuit | Overcurrent | P0617 | ·
Starter Relay Overcurrent ·
Starter Circuit Abnoml ·
Starter Circuit Open |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
BBC NO. 1 fuse ·
BBC NO 2 fuse ·
Wire harness or connector ·
ST relay ·
Engine stop and start ECU |
| Stuck on | P1644 | ·
Wire harness or connector ·
ST relay ·
Engine stop and start ECU |
|||
| Stuck off | P1644 | ||||
| BBC (backup boost converter) circuit | Overcurrent | B22C0 | ·
State of BBC ·
BBC Abnoml ·
BBC Overcurrent ·
BBC Check Result |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery ·
ECUs and sensors connected to B41, B42 and IG41 |
·
Open ·
Shorted ·
Internal circuit malfunction ·
Battery |
P323B | ·
State of BBC ·
BBC Duty ·
BBC Thermistor ·
BBC Abnoml ·
BBC Over Heat ·
BBC Power Low |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery |
|
| ECU inner circuit | Malfunction | P0607 | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
Engine stop and start ECU |
| Monitoring CPU circuit | Malfunction | P060A | State of BBC | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
Engine stop and start ECU |
| EEPROM | Malfunction | P062F | EEPROM | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
Engine stop and start ECU |
| Malfunctioning Area | Malfunction | DTC Output | Data List / Freeze Frame Data | Effect on Vehicle | Area to be Inspected |
|---|---|---|---|---|---|
| SFI system | MIL illuminated | DTCs for SFI system output | ·
Oper Permission (ECM 1) ·
Oper Permission (ECM 2) |
Stop and start control prohibited | SFI system |
| Abnormal NE signal | DTCs for SFI system output | ·
NE Sensor Circuit Open 2 ·
Crank Pos Sen Abnoml 3 |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
SFI system (crankshaft position sensor circuit) ·
Wire harness or connector |
|
| Crankshaft reverse rotation detection | DTCs for SFI system output | - | ·
Stop and start control prohibited ·
MIL illuminated |
SFI system (crankshaft position sensor circuit) | |
| Charging system | Battery state sensor assembly malfunction | DTCs for charging system output | ·
Battery Fluid Temperature ·
Integrated Current |
Stop and start control prohibited | Charging system |
| Vehicle stability control system | VSC Running | - | ABS Running | Stop and start control prohibited | - |
| Malfunction in wheel speed sensor | Brake control system DTCs output | ·
Vehicle Spd1 (ABS/VSC) ·
Wheel Speed Malfunction |
Stop and start control prohibited | ·
Wire harness or connector ·
Skid control ECU (Brake actuator assembly) ·
Vehicle speed sensor |
|
| Power steering system | Malfunction in power steering system | EPS assist current value invalid | ·
EPS Load ·
Comm Err with EPS |
Stop and start control prohibited | ·
Power steering ECU assembly ·
Torque sensor |
| Seat belt warning system | Malfunction in seat belt warning system | - | Oper Permission (Driver Side Buckle SW) | ·
Stop and start control prohibited (stuck off) ·
Engine does not restart when it is stopped by stop and start control (stuck on) |
·
Front seat inner belt assembly (for driver side) ·
Wire harness or connector |
| Driver door courtesy light switch circuit | Malfunction in driver door courtesy light switch circuit | - | D Courtesy Switch Signal | ·
Stop and start control prohibited (stuck off) ·
Engine does not restart when it is stopped by stop and start control (stuck on) |
·
Front door courtesy light switch assembly (for driver side) ·
Driver door courtesy light switch circuit |
| Air conditioning system | Malfunction in ambient temperature sensor | Air conditioning system DTCs output | Ambient Temp Sensor | Stop and start control prohibited | Ambient temperature sensor circuit |
| Brake vacuum | Brake booster vacuum drops | - | ·
Brake Boost Pressure ·
Brake Negative Pressure ·
Brk Boost Sen Abnoml 1 ·
Brk Boost Sen Abnoml 2 ·
Brk Boost Sen Abnoml 3 |
Stop and start control prohibited | ·
Brake booster vacuum ·
Brake booster assembly ·
Vacuum sensor assembly ·
Vacuum hose (brake booster hose) |
| Power source | Backup boost converter malfunction | P323B | ·
State of BBC ·
BBC Duty ·
BBC Thermistor ·
BBC Abnoml ·
BBC Over Heat ·
BBC Power Low |
·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Wire harness or connector ·
Engine stop and start ECU ·
Battery |
| Charging system malfunction | - | Alternator Status | Stop and start control prohibited | Charging system | |
| Low voltage | P0562 | Battery Abnoml | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Battery ·
Relay |
|
| Number of starter operations | Exceeds the specified limit | P1545 | Starter Count Abnoml | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Starter assembly replacement is required. ·
ST relay replacement is required. ·
Fuse replacement is required. |
| Starter signal malfunction | Signal does not match with the starter switch | P1545 | - | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Wire harness or connector ·
Engine stop and start ECU |
| Jump start | Engine started with the engine hood open | - | Eng Start Req (Engine Hood Open) | Stop and start control prohibited
(permitted when the ignition switch is turned off) |
·
Check for history of roadside service or jump start due to dead battery ·
Engine hood courtesy switch (Hood lock assembly) |
| CAN communication | Communication interrupted | U0100
U0121 U0126 U0131 U0140 U0151 U0164 U1110 |
- | ·
Stop and start control prohibited ·
Stop and start cancel indicator light blinks |
·
Applicable wire harness or connector ·
Applicable ECU |
*: The stop and start cancel indicator light does not blink when a communication error with the combination meter assembly occurs.