Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM U

STOP AND START  STOP AND START SYSTEM  TERMINALS OF ECU  


ENGINE STOP AND START ECU


A392127E01
1.51,0.323 2.01,0.573 0.5,0.25 3.167,0.333 3.667,0.583 0.5,0.25 4.917,0.333 5.417,0.583 0.5,0.25 5.5,2.083 6,2.333 0.5,0.25 3.167,2.083 3.667,2.333 0.5,0.25 1.073,2.083 1.573,2.333 0.5,0.25 1.646,0.344 2.104,0.542 0.458,0.198 10 false A61 3.302,0.354 3.76,0.552 0.458,0.198 10 false A62 5.052,0.354 5.51,0.552 0.458,0.198 10 false F77 5.635,2.115 6.094,2.313 0.458,0.198 10 false F77 3.302,2.104 3.76,2.302 0.458,0.198 10 false A62 1.208,2.104 1.667,2.302 0.458,0.198 10 false A61

a.

Disconnect the A61, A62 and F77 engine stop and start ECU connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A61-1 (BIN2) - Body ground W - Body ground Battery Always 9.5 to 14 V
A61-2 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
A61-3 (BIN1) - Body ground B - Body ground Battery Always 9.5 to 14 V
A61-8 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
A62-1 (+B) - Body ground B - Body ground Power source of engine stop and start ECU Ignition switch ON 9.5 to 14 V
A62-6 (DGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A62-10 (NE) - Body ground L - Body ground Engine speed signal from ECM Always 10 kΩ or higher
F77-13 (CANH) - Body ground R - Body ground CAN communication Always 200 Ω or higher
F77-14 (CANL) - Body ground P - Body ground CAN communication Always 200 Ω or higher
F77-18 (IG2) - Body ground L - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V
F77-19 (ACC) - Body ground R - Body ground Ignition switch signal Ignition switch ACC 9.5 to 14 V
F77-21 (IG1) - Body ground V - Body ground Ignition switch signal Ignition switch ON 9.5 to 14 V


c.

Reconnect the A61, A62 and F77 engine stop and start ECU connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A62-3 (BRE2) - Body ground LG - Body ground Ground (vacuum sensor assembly (brake booster pressure sensor)) Always Below 1 Ω
A62-7 (BNT1) - A62-6 (DGND) R - W-B Engine hood courtesy switch (Hood lock assembly) signal
·

Ignition switch ON

·

Engine stopped

·

Engine hood closed


0 to 1.5 V
·

Ignition switch ON

·

Engine stopped

·

Engine hood open


8 to 14 V
A62-8 (TMN) - A62-25 (TME2) V - GR Neutral position switch signal
·

Ignition switch ON

·

Shift lever in neutral


2.7 to 4.3 V
·

Ignition switch ON

·

Shift lever in any other than neutral


0.7 to 1.9 V
A62-10 (NE) - A62-6 (DGND) L - W-B Engine speed signal from ECM Idling after engine warmed up Pulse generation
(see waveform)
A62-13 (PB) - A62-3 (BRE2) V - LG Vacuum sensor assembly (brake booster pressure sensor) signal
·

Ignition switch ON

·

Absolute pressure of 40 kPa 40 kPa (0.4 kgf/cm2, 5.8 psi) applied to vacuum sensor assembly (brake booster pressure sensor)


1.6 to 2.0 V
·

Ignition switch ON

·

Absolute pressure of 60 kPa (0.6 kgf/cm2, 8.7 psi) applied to vacuum sensor assembly (brake booster pressure sensor)


2.2 to 2.6 V
·

Ignition switch ON

·

Atmospheric pressure applied to vacuum sensor assembly (brake booster pressure sensor)


3.4 to 3.8 V
A62-14 (BRVC) - A62-6 (DGND) P - W-B Vacuum sensor assembly (brake booster pressure sensor) power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
A62-17 (CLL) - A62-6 (DGND) W - W-B Clutch start switch assembly signal
·

Ignition switch ON

·

Clutch pedal released


8 to 14 V
·

Ignition switch ON

·

Clutch pedal fully depressed


Below 1.5 V
A62-21 (STA) - A62-6 (DGND) LG - W-B Starter pinion operation signal Cranking 6.0 V or more
A62-26 (TMVC) - A62-6 (DGND) W - W-B Neutral position switch power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
F77-1 (IG31) - A62-6 (DGND) V - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
F77-2 (B41) - A62-6 (DGND) SB - W-B Backup boost converter signal Always 10.5 to 16 V
F77-3 (IG41) - A62-6 (DGND) BE- W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
F77-5 (ECAN) - A62-6 (DGND) P - W-B Stop and start system cancel switch (Electric parking brake switch assembly) signal
·

Ignition switch ON

·

Stop and start system cancel switch (Electric parking brake switch assembly) pressed


0 to 1.5 V
·

Ignition switch ON

·

Stop and start system cancel switch (Electric parking brake switch assembly) not pressed


8 to 14 V
F77-6 (IG11) - A62-6 (DGND) LG - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
F77-10 (IG12) - A62-6 (DGND) P - W-B Backup boost converter signal Ignition switch ON 10.5 to 16 V
F77-12 (B42) - A62-6 (DGND) SB - W-B Backup boost converter signal Always 10.5 to 16 V
F77-18 (IG2) - A62-6 (DGND) L - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
F77-19 (ACC) - A62-6 (DGND) R - W-B Ignition switch signal Ignition switch off Below 1 V
Ignition switch ACC 9.5 to 14 V
F77-21 (IG1) - A62-6 (DGND) V - W-B Ignition switch signal Ignition switch ACC Below 1 V
Ignition switch ON 9.5 to 14 V
F77-24 (AC41) - A62-6 (DGND) GR - W-B Backup boost converter signal Ignition switch ACC 10.5 to 16 V


e.
A318633E03
2.792,1.042 3.25,1.24 0.458,0.198 10 false GND 0.26,0.073 1.49,0.271 1.229,0.198 10 false 5 V/DIV. 1.313,1.906 2.844,2.104 1.531,0.198 10 false 2 ms./DIV.

Waveform

Item Content
Tester Connection A62-10 (NE) - A62-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling after engine warmed up