Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295448 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio receiver assembly.

WIRING DIAGRAM

E358181E02
1.146,0.646 2.979,0.844 1.833,0.198 10 false from Battery 0.927,1.427 2.76,1.625 1.833,0.198 10 false from ACC Relay 3.26,0.875 4.031,1.073 0.771,0.198 10 false RADIO 3.177,1.688 3.948,1.885 0.771,0.198 10 false ECU-ACC 5.031,2.979 5.802,3.177 0.771,0.198 10 false F48 5.031,3.156 6.719,3.354 1.688,0.198 10 false Radio Receiver Assembly 5.208,0.667 5.667,0.865 0.458,0.198 10 false +B1 5.208,1.448 5.667,1.646 0.458,0.198 10 false ACC1 5.208,2.25 5.667,2.448 0.458,0.198 10 false GND1 5.031,0.563 5.323,0.792 0.292,0.229 10 false 4 5.021,1.333 5.313,1.563 0.292,0.229 10 false 3 5.042,2.135 5.333,2.365 0.292,0.229 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the radio receiver assembly connector.


b.
E360338C01
1.427,0.302 1.865,0.583 0.438,0.281 2.198,0.99 2.594,0.823 true 1.979,1 2.198,0.656 true 1.385,1.677 1.604,1.333 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.531,0.344 1.844,0.542 0.313,0.198 10 false F48 1.156,1.729 1.635,1.969 0.479,0.24 10 false GND1 2.656,0.74 2.969,0.938 0.313,0.198 10 false +B1 2.208,0.49 2.688,0.729 0.479,0.24 10 false ACC1
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F48-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F48-4 (+B1) - F48-7 (GND1) Always 11 to 14 V
F48-3 (ACC1) - F48-7 (GND1) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR