Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY (for TMMT Made)
RM32H0E _52 Drivetrain _060137 DRIVE SHAFT / PROPELLER SHAFT _0295579 REAR DRIVE SHAFT ASSEMBLY(for TMMT Made) A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY(for TMMT Made)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42347E 1.SEPARATE REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

C129490

a.

Using needle-nose pliers, separate the rear No. 2 drive shaft inboard joint boot clamp LH as shown in the illustration.


Hide 42347D 2.SEPARATE REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

a.
C282244

Using pliers, separate the rear drive shaft inboard joint boot clamp LH.


Hide 3.SEPARATE REAR DRIVE SHAFT INBOARD JOINT BOOT LH

a.

Separate the rear drive shaft inboard joint boot LH from the rear drive shaft inboard joint assembly LH.


Hide 42360D 4.REMOVE REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY LH

a.

Remove the old grease from the rear drive shaft inboard joint assembly LH.


b.
C158439C17
1.385,1.24 1.125,0.458 1.125,0.458 1.927,0.667 true 0.948,0.365 1.344,0.521 0.396,0.156 10 *a
*a Matchmark


Put matchmarks on the rear drive shaft inboard joint assembly LH and rear drive outboard joint shaft assembly LH.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the rear drive shaft inboard joint assembly LH from the rear drive outboard joint shaft assembly LH.


d.
C265836

Remove the rear axle inboard joint grommet from the rear drive shaft inboard joint assembly LH.


e.
C160822

Using a snap ring expander, remove the rear drive shaft snap ring LH from the rear drive outboard joint shaft assembly LH.


f.
C316793C05
3.031,1.177 2.208,1.844 2.208,1.844 3.083,1.26 true 2.031,1.771 2.344,1.927 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear drive outboard joint shaft assembly LH and tripod joint.

NOTICE:

Do not use a punch to make the matchmarks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the rear drive outboard joint shaft assembly LH.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




h.

Remove the rear No. 2 drive shaft inboard joint boot clamp LH, rear drive shaft inboard joint boot LH and rear drive shaft inboard joint boot clamp LH.


Hide 42346F 5.SEPARATE REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

C081167

a.

Using pliers, separate the rear No. 2 drive shaft outboard joint boot clamp LH.


Hide 42346D 6.SEPARATE REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

a.

Perform the same procedure as for the rear No. 2 drive shaft outboard joint boot clamp LH.


Hide 7.REMOVE REAR DRIVE SHAFT OUTBOARD JOINT BOOT

a.

Remove the rear drive shaft outboard joint boot LH from the rear drive outboard joint shaft assembly LH.


b.

Remove any old grease from the rear drive outboard joint shaft assembly LH.


Hide 41336K 8.REMOVE REAR DRIVE SHAFT DUST COVER LH

C127659N02
0.792,1.771 0.969,1.771 0.969,1.771 1.208,1.385 true 0.438,1.698 0.865,1.844 0.427,0.146 10 SST

HINT:

Only perform the following procedure if the rear drive shaft dust cover LH is deformed.


a.

Using SST and a press, remove the rear drive shaft dust cover LH.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the rear drive shaft inboard joint assembly LH.

·

Do not overtighten SST.