Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY (for TMC Made)
RM32H0E _52 Drivetrain _060137 DRIVE SHAFT / PROPELLER SHAFT _0295582 REAR DRIVE SHAFT ASSEMBLY(for TMC Made) A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY(for TMC Made)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 42347E 1.SEPARATE REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

C129490

a.

Using needle-nose pliers, separate the rear No. 2 drive shaft inboard joint boot clamp LH as shown in the illustration.


Hide 42347D 2.SEPARATE REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the rear No. 2 drive shaft inboard joint boot clamp LH.


Hide 3.SEPARATE REAR DRIVE SHAFT INBOARD JOINT BOOT LH

a.

Separate the rear drive shaft inboard joint boot LH from the rear drive shaft inboard joint assembly LH.


Hide 42360D 4.REMOVE REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY LH

C129505C01
1.76,1 1.333,0.25 1.333,0.25 2.083,0.594 true 1.125,0.125 1.844,0.271 0.719,0.146 10 false *a
*a Matchmark


a.

Remove any old grease from the rear drive shaft inboard joint assembly LH.


b.

Put matchmarks on the rear drive shaft inboard joint assembly LH and rear drive outboard joint shaft assembly LH.

NOTICE:

Do not use a punch to make the matchmarks.



c.

Remove the rear drive shaft inboard joint assembly LH from the rear drive outboard joint shaft assembly LH.


d.
C160822

Using a snap ring expander, remove the rear drive shaft snap ring LH from the rear drive outboard joint shaft assembly LH.


e.
C162724C12
2.906,0.531 1.521,0.313 1.521,0.313 3,0.615 true 1.344,0.24 1.542,0.406 0.198,0.167 10 false *a
*a Matchmark


Put matchmarks on the rear drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch to make the matchmarks.



f.

Using a brass bar and hammer, remove the tripod joint from the rear drive outboard joint shaft assembly LH.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




g.

Remove the rear drive shaft inboard joint boot LH.


Hide 42346F 5.SEPARATE REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

C277140

a.

Using a screwdriver, separate the rear No. 2 drive shaft outboard joint boot clamp LH as shown in the illustration.


Hide 42346D 6.SEPARATE REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

C277139

a.

Using pliers, separate the rear drive shaft outboard joint boot clamp LH as shown in the illustration.


Hide 7.REMOVE REAR DRIVE SHAFT OUTBOARD JOINT BOOT LH

a.

Remove the rear drive shaft outboard joint boot LH from the rear drive shaft outboard joint shaft assembly LH.


b.

Remove any old grease from the rear drive shaft outboard joint shaft assembly LH.


Hide 41336K 8.REMOVE REAR DRIVE SHAFT DUST COVER LH

C127659N02
0.792,1.771 0.969,1.771 0.969,1.771 1.208,1.385 true 0.438,1.698 0.865,1.844 0.427,0.146 10 SST

HINT:

Only perform the following procedure if the rear drive shaft dust cover LH is deformed.


a.

Using SST and a press, remove the rear drive shaft dust cover LH.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the front drive inboard joint assembly.

·

Do not overtighten SST.