Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0295680 DIFFERENTIAL CASE G

EC6A MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  INSPECTION  


PROCEDURE

Hide 41300 1.INSPECT FRONT DIFFERENTIAL CASE ASSEMBLY WITH RING GEAR

a.
C290766N02
1.76,1.948 2,1.729 2,1.729 2.208,1.729 true 2.271,1.656 2.729,1.854 0.458,0.198 10 false SST

Using SST, rotate the front differential side gear as shown in the illustration.

SST
09528-52010  (09528-05040)

Standard:

The front differential side gear does not lock when rotated in either direction.


·

If the front differential side gear locks, perform all inspections.

·

If the front differential side gear still locks even after replacing the malfunctioning parts, replace the front differential case assembly with ring gear.



Hide 2.INSPECT FRONT DIFFERENTIAL SIDE GEAR THRUST AMOUNT

a.

Secure the front differential case assembly with ring gear in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C290767C02
0.677,0.573 0.875,0.573 0.875,0.573 1.375,1.208 true 0.375,0.49 0.833,0.688 0.458,0.198 10 false SST 2.74,2.958 2.948,3.125 0.208,0.167 10 true *a
*a Front Differential Side Gear Thrust Amount


Using SST and a dial indicator, measure the front differential side gear thrust amount.

SST
09528-52010  (09528-05040)

Front Differential Side Gear Thrust Amount:

0.08 mm (0.00315 in.) or less


HINT:
·

Measure the front differential side gear thrust amount while slowly rotating the front differential side gear.

·

Make sure to measure the front differential side gear thrust amount for both of the 2 front differential side gears.



If the result is not as specified, replace the 2 front differential side gears, 2 front differential pinions and 2 conical springs.


Hide 3.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

a.

Install SST as shown in the illustration and tighten it.

C290768C02
5.01,0.49 5.219,0.49 5.219,0.49 5.396,0.292 false 4.729,1.563 5.146,1.563 5.146,1.563 5.302,1.406 true 5.156,1.573 5.292,1.708 true 3.271,0.49 3.583,0.688 0.313,0.198 10 false *a 0.802,2.427 1.115,2.625 0.313,0.198 10 false *b 4.708,0.396 5.167,0.594 0.458,0.198 10 false SST 4.448,1.479 4.906,1.677 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09953-05010, 09528-05020)

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Secure the front differential case assembly with ring gear in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.
C332310C01
2.615,0.24 2.896,0.24 false 2.938,0.125 3.271,0.448 0.333,0.323 10 false *1
*1 Front No. 1 Differential Pinion Shaft


Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.


d.

Using a dial indicator, measure the front differential pinion backlash.

Standard Backlash:

0.20 mm (0.00787 in.) or less


If the backlash is not as specified, replace the front No. 1 differential side gear thrust washers with washers of a different thickness. Use the table below to select a front No. 1 differential side gear thrust washer which will ensure that the backlash is within the specification.

Front No. 1 Differential Side Gear Thrust Washer Thickness:
Mark Thickness mm (in.)
19 0.90 (0.0354)
14 0.95 (0.0374)
02 1.00 (0.0394)
15 1.05 (0.0413)
03 1.10 (0.0433)
16 1.15 (0.0453)
04 1.20 (0.0472)


HINT:

Select front No. 1 differential side gear thrust washers of the same thickness for both the right and left side.



Hide 41351F 4.INSPECT FRONT DIFFERENTIAL PINION THRUST WASHER

a.
C288044

Using a micrometer, measure the thickness of the front differential pinion thrust washer.

Minimum Thickness:

0.94 mm (0.0370 in.)


HINT:

Measure the most worn portion of the front differential pinion thrust washer.


If the thickness is less than the minimum, replace the front differential pinion thrust washer.


Hide 41342F 5.INSPECT FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C199374

Using a micrometer, measure the outer diameter of the front No. 1 differential pinion shaft.

Minimum Outer Diameter:

16.982 mm (0.669 in.)


HINT:

Measure the most worn portion of the front No. 1 differential pinion shaft.


If the outer diameter is less than the minimum, replace the front No. 1 differential pinion shaft.