Home › Drivetrain › EC69 (MANUAL TRANSMISSION / TRANSAXLE) › INPUT SHAFT › 2016.10–2019.09
RM32H0E _52 Drivetrain _060311 EC69 MANUAL TRANSMISSION / TRANSAXLE _0295684 INPUT SHAFT G

EC69 MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  INSPECTION  


PROCEDURE

Hide 1.INSPECT 6TH GEAR THRUST CLEARANCE

a.
C194221

Using a dial indicator, measure the 6th gear thrust clearance.

Standard Clearance:

0.15 to 0.43 mm (0.00591 to 0.0169 in.)


Maximum Clearance:

0.43 mm (0.0169 in.)


If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, 6th gear sub-assembly or input shaft.


Hide 2.INSPECT 5TH GEAR THRUST CLEARANCE

a.
C194226

Using a dial indicator, measure the 5th gear thrust clearance.

Standard Clearance:

0.15 to 0.43 mm (0.00591 to 0.0169 in.)


Maximum Clearance:

0.43 mm (0.0169 in.)


If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, 5th gear or input shaft.


Hide 3.INSPECT 4TH GEAR THRUST CLEARANCE

a.
C194227

Using a dial indicator, measure the 4th gear thrust clearance.

Standard Clearance:

0.15 to 0.56 mm (0.00591 to 0.0220 in.)


Maximum Clearance:

0.56 mm (0.0220 in.)


If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 4th gear or input shaft.


Hide 4.INSPECT 3RD GEAR THRUST CLEARANCE

a.
C194228

Using a dial indicator, measure the 3rd gear thrust clearance.

Standard Clearance:

0.15 to 0.43 mm (0.00591 to 0.0169 in.)


Maximum Clearance:

0.43 mm (0.0169 in.)


If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 3rd gear or input shaft.


Hide 5.INSPECT 6TH GEAR RADIAL CLEARANCE

a.
C194222

Using a dial indicator, measure the 6th gear radial clearance between the gear and shaft.

Standard Clearance:

0.009 to 0.045 mm (0.000354 to 0.00177 in.)


Maximum Clearance:

0.045 mm (0.00177 in.)


If the clearance exceeds the maximum, replace the 6th gear sub-assembly, 6th gear needle roller bearing, inner 6th gear bearing race or input shaft.


Hide 6.INSPECT 5TH GEAR RADIAL CLEARANCE

a.
A295381

Using a dial indicator, measure the 5th gear radial clearance between the gear and shaft.

Standard Clearance:

0.009 to 0.045 mm (0.000354 to 0.00177 in.)


Maximum Clearance:

0.045 mm (0.00177 in.)


If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing, inner 5th gear bearing race or input shaft.


Hide 7.INSPECT 4TH GEAR RADIAL CLEARANCE

a.
C194224

Using a dial indicator, measure the 4th gear radial clearance between the gear and shaft.

Standard Clearance:

0.009 to 0.050 mm (0.000354 to 0.0197 in.)


Maximum Clearance:

0.050 mm (0.0197 in.)


If the clearance exceeds the maximum, replace the 4th gear, 4th gear needle roller bearing or input shaft.


Hide 8.INSPECT 3RD GEAR RADIAL CLEARANCE

a.
A295382

Using a dial indicator, measure the 3rd gear radial clearance.

Standard Clearance:

0.009 to 0.050 mm (0.000354 to 0.0197 in.)


Maximum Clearance:

0.050 mm (0.0197 in.)


If the clearance exceeds the maximum, replace the 3rd gear, 3rd gear needle roller bearing or input shaft.


Hide 33311 9.INSPECT INPUT SHAFT

a.
C194251

Using a dial indicator, check the input shaft runout.

Maximum Runout:

0.03 mm (0.00118 in.)


If the runout exceeds the maximum, replace the input shaft.


b.
C194252N13
1.073,3.135 1.323,3.344 0.25,0.208 10 false A 1.958,3.135 2.104,3.344 0.146,0.208 10 false B 2.51,3.156 2.656,3.365 0.146,0.208 10 false D 3.083,3.167 3.229,3.375 0.146,0.208 10 false E 2.865,3.167 3.01,3.375 0.146,0.208 10 false E 2.344,3.125 2.49,3.333 0.146,0.208 10 false C 2.677,3.156 2.823,3.365 0.146,0.208 10 false D

Using a micrometer, measure the outer diameter of the input shaft journal surface at the locations indicated.

Standard Outer Diameter:
Part A:

25.002 to 25.017 mm (0.9843 to 0.9849 in.)

Part B:

37.485 to 37.500 mm (1.4758 to 1.4764 in.)

Part C:

37.496 to 37.500 mm (1.4762 to 1.4764 in.)

Part D:

31.690 to 31.700 mm (1.2476 to 1.2480 in.)

Part E:

27.990 to 28.000 mm (1.1019 to 1.1023 in.)


Minimum Outer Diameter:
Part A:

25.002 mm (0.9843 in.)

Part B:

37.485 mm (1.4757 in.)

Part C:

37.496 mm (1.4762 in.)

Part D:

31.690 mm (1.2476 in.)

Part E:

27.990 mm (1.1019 in.)


If any of the outer diameters are less than the minimum, replace the input shaft.


Hide 3335A 10.INSPECT INNER 6TH GEAR BEARING RACE

a.
C194375

Using a micrometer, measure the outer diameter of the inner 6th gear bearing race.

Standard Outer Diameter:

35.09 to 35.10 mm (1.3814 to 1.3818 in.)


Minimum Outer Diameter:

35.09 mm (1.3814 in.)


If the outer diameter is less than the minimum, replace the inner 6th gear bearing race.


b.
C194377

Using a cylinder gauge, measure the inside diameter of the inner 6th gear bearing race.

Standard Inside Diameter:

28.005 to 28.020 mm (1.1025 to 1.1031 in.)


Maximum Inside Diameter:

28.020 mm (1.1031 in.)


If the inside diameter exceeds the maximum, replace the inner 6th gear bearing race.


Hide 33359 11.INSPECT INNER 5TH GEAR BEARING RACE

a.
C194374

Using a micrometer, measure the outer diameter of the inner 5th gear bearing race.

Standard Outer Diameter:

37.49 to 37.50 mm (1.4759 to 1.4763 in.)


Minimum Outer Diameter:

37.49 mm (1.4759 in.)


If the outer diameter is less than the minimum, replace the inner 5th gear bearing race.


b.
C194376

Using a cylinder gauge, measure the inside diameter of the inner 5th gear bearing race.

Standard Inside Diameter:

31.705 to 31.720 mm (1.2482 to 1.2488 in.)


Maximum Inside Diameter:

31.720 mm (1.2488 in.)


If the inside diameter exceeds the maximum, replace the inner 5th gear bearing race.


Hide 33337 12.INSPECT 6TH GEAR SUB-ASSEMBLY

a.
C194253

Using a cylinder gauge, measure the inside diameter of the 6th gear sub-assembly.

Standard Inside Diameter:

40.109 to 40.125 mm (1.5790 to 1.5797 in.)


Maximum Inside Diameter:

40.125 mm (1.5797 in.)


If the inside diameter exceeds the maximum, replace the 6th gear sub-assembly.


Hide 33336 13.INSPECT 5TH GEAR

a.
C194254

Using a cylinder gauge, measure the inside diameter of the 5th gear.

Standard Inside Diameter:

42.509 to 42.525 mm (1.6735 to 1.6742 in.)


Maximum Inside Diameter:

42.525 mm (1.6742 in.)


If the inside diameter exceeds the maximum, replace the 5th gear.


Hide 33334 14.INSPECT 4TH GEAR

a.
C194255

Using a cylinder gauge, measure the inside diameter of the 4th gear.

Standard Inside Diameter:

42.509 to 42.525 mm (1.6735 to 1.6742 in.)


Maximum Inside Diameter:

42.525 mm (1.6742 in.)


If the inside diameter exceeds the maximum, replace the 4th gear.


Hide 33333 15.INSPECT 3RD GEAR

a.
C194256

Using a cylinder gauge, measure the inside diameter of the 3rd gear.

Standard Inside Diameter:

42.509 to 42.525 mm (1.6735 to 1.6742 in.)


Maximum Inside Diameter:

42.525 mm (1.6742 in.)


If the inside diameter exceeds the maximum, replace the 3rd gear.


Hide 33396C 16.INSPECT NO. 5 SYNCHRONIZER RING

a.
C204180C02
0.473,0.208 0.684,0.364 0.212,0.156 10 *a
*a Locks


Check for wear and damage.


b.

Coat the 6th gear cone with gear oil.


c.

Coat the 5th gear cone with gear oil.


d.

Turn the synchronizer ring in one direction while pushing it against the 6th gear cone.


e.

Check that the ring locks.

If the synchronizer ring does not lock, replace the synchronizer ring.


f.

Turn the synchronizer ring in one direction while pushing it against the 5th gear cone.


g.

Check that the ring locks.

If the synchronizer ring does not lock, replace the synchronizer ring.


h.
C194260

Using a feeler gauge, measure the clearance between the synchronizer ring and the gear spline end.

Standard Clearance:

0.73 to 1.53 mm (0.0287 to 0.0602 in.)


Minimum Clearance:

0.73 mm (0.0287 in.)


If the clearance is less than the minimum, replace the synchronizer ring.


Hide 33381 17.INSPECT OUTER 2ND SYNCHRONIZER RING

a.
C204834C02
0.722,0.165 0.899,0.335 0.177,0.17 10 *a
*a Locks


Check for wear and damage.


b.

Coat the 4th gear cone with gear oil.


c.

Turn the synchronizer ring in one direction while pushing it against the 4th gear cone.


d.

Check that the ring locks.

If the synchronizer ring does not lock, replace the synchronizer ring.


e.
C194261

Using a feeler gauge, measure the clearance between the synchronizer ring and the gear spline end.

Standard Clearance:

0.78 to 1.58 mm (0.0307 to 0.0622 in.)


Minimum Clearance:

0.78 mm (0.0307 in.)


If the clearance is less than the minimum, replace the synchronizer ring.


Hide 33369 18.INSPECT NO. 3 SYNCHRONIZER RING

a.
C204835C02
0.804,0.182 1.008,0.352 0.205,0.17 10 *a
*a Locks


Check for wear and damage.


b.

Coat the 3rd gear cone with gear oil.


c.

Turn the synchronizer ring in one direction while pushing it against the 3rd gear cone.


d.

Check that the ring locks.

If the synchronizer ring does not lock, replace the synchronizer ring.


e.
C194262

Using a feeler gauge, measure the clearance between the synchronizer ring and the gear spline end.

Standard Clearance:

0.78 to 1.58 mm (0.0307 to 0.0622 in.)


Minimum Clearance:

0.78 mm (0.0307 in.)


If the clearance is less than the minimum, replace the synchronizer ring.


Hide 33364 19.INSPECT NO. 2 TRANSMISSION HUB SLEEVE

a.
C194263

Check the sliding condition between the No. 2 transmission hub sleeve and the No. 2 transmission clutch hub.


b.

Check that the edges of the No. 2 transmission hub sleeve splines are not worn down.


c.
C194265C02
1.333,3.313 1.469,3.469 0.135,0.156 10 A 0.365,1.917 0.5,2.073 0.135,0.156 10 B 0.24,4.01 1.156,4.208 0.917,0.198 10 *a = A - B
*a Clearance


Using a vernier caliper, measure the width of the No. 2 transmission hub sleeve groove (A) and the thickness of the claw part on the No. 2 gear shift fork (B), and calculate the clearance.

Standard Clearance (A - B):

0.1 to 0.5 mm (0.00394 to 0.0197 in.)


If the clearance is out of specification, replace the No. 2 transmission hub sleeve and No. 2 gear shift fork.


Hide 33395 20.INSPECT NO. 3 TRANSMISSION HUB SLEEVE

a.
C194264

Check the sliding condition between the No. 3 transmission hub sleeve and the No. 3 transmission clutch hub.


b.

Check that the edges of the No. 3 transmission hub sleeve splines are not worn down.


c.
C194266C02
0.354,1.927 0.479,2.083 0.125,0.156 10 B 1.333,3.458 1.458,3.615 0.125,0.156 10 A 0.219,4.073 1.75,4.271 1.531,0.198 10 *a = A - B
*a Clearance


Using a vernier caliper, measure the width of the No. 3 transmission hub sleeve groove (A) and the thickness of the claw part on the No. 3 gear shift fork (B), and calculate the clearance.

Standard Clearance (A - B):

0.1 to 0.5 mm (0.00394 to 0.0197 in.)


If the clearance is out of specification, replace the No. 3 transmission hub sleeve and No. 3 gear shift fork.