Home › Drivetrain › EC69 (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL CASE › 2016.10–2019.09
RM32H0E _52 Drivetrain _060311 EC69 MANUAL TRANSMISSION / TRANSAXLE _0295687 DIFFERENTIAL CASE A

EC69 MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 41300 1.INSPECT FRONT DIFFERENTIAL CASE ASSEMBLY WITH RING GEAR

Hide 2.INSPECT FRONT DIFFERENTIAL SIDE GEAR THRUST AMOUNT

Hide 41342A 3.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.

Secure the front differential case assembly with ring gear in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C292459

Using a 5 mm pin punch and a hammer, remove the front differential pinion shaft straight pin from the front differential case assembly with ring gear.


Hide 41342F 4.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C263879

Remove the front No. 1 differential pinion shaft from the front differential case assembly with ring gear.


Hide 5.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 6.REMOVE FRONT DIFFERENTIAL SIDE GEAR

a.

Install SST as shown in the illustration and tighten it.

C290763C03
4.698,0.563 4.865,0.563 4.865,0.563 5.125,0.292 false 4.469,1.594 4.854,1.594 4.854,1.594 5.031,1.396 true 4.865,1.594 5.031,1.719 true 3.229,0.24 3.542,0.438 0.313,0.198 10 false *a 1.073,2.427 1.385,2.625 0.313,0.198 10 false *b 4.385,0.49 4.917,0.76 0.531,0.271 10 false SST 4.146,1.51 4.604,1.708 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09953-05010, 09528-05020)

NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case assembly with ring gear.


HINT:
·

Tighten SST until there is clearance between the front differential pinions and front differential side gears.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C290764C04
2.719,2.813 2.563,2.813 2.563,2.813 2.563,2.375 true 1.656,0.75 1.969,0.948 0.313,0.198 10 false *a 2.781,2.729 3.24,2.927 0.458,0.198 10 false SST
*a Turn


Install SST as shown in the illustration, rotate the front differential side gear, and then remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front differential case assembly with ring gear.

SST
09528-52010  (09528-05040)

NOTICE:

Do not drop the front differential pinion and front differential pinion thrust washer.



c.
C304161C01
2.292,1.865 2.406,1.865 false 2.292,0.323 2.427,0.323 false 2.302,0.552 2.573,0.552 false 2.292,1.49 2.573,1.49 false 2.292,1.708 2.427,1.708 false 2.292,0.177 2.406,0.177 false 2.104,0.5 2.417,0.698 0.313,0.198 10 false *1 2.115,1.427 2.427,1.625 0.313,0.198 10 false *1 2.104,0.271 2.417,0.469 0.313,0.198 10 false *2 2.104,0.104 2.417,0.302 0.313,0.198 10 false *3 2.115,1.646 2.427,1.844 0.313,0.198 10 false *2 2.115,1.802 2.427,2 0.313,0.198 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front differential case assembly with ring gear, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs from the front differential case assembly with ring gear.

NOTICE:

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring.