Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295690 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E360247E01
5.5,2.677 5.813,2.875 0.313,0.198 10 false j2 5.438,2.896 7.156,3.75 1.719,0.854 10 false Radio and Display Receiver Assembly 2.5,3.281 5.344,3.802 2.844,0.521 10 false : Data Signal (USB Communication Line) 0.469,2.865 1.615,3.781 1.146,0.917 10 false No. 1 Stereo Jack Adapter Assembly 0.5,2.677 0.813,2.875 0.313,0.198 10 false j1 3.292,1.75 4.823,1.948 1.531,0.198 10 false (Shielded) 5.906,0.677 7.156,0.906 1.25,0.229 10 false US1- 5.906,1.458 7.156,1.688 1.25,0.229 10 false US1+ 5.906,2.229 7.156,2.458 1.25,0.229 10 false USG1 5.708,0.5 5.865,0.698 0.156,0.198 10 false 2 5.688,1.292 5.844,1.49 0.156,0.198 10 false 3 5.708,2.094 5.865,2.292 0.156,0.198 10 false 5 1.354,0.51 1.51,0.708 0.156,0.198 10 false 2 1.344,1.313 1.5,1.51 0.156,0.198 10 false 3 1.333,2.104 1.49,2.302 0.156,0.198 10 false 5 0.906,0.667 1.292,1.115 0.385,0.448 10 false UDO- 0.865,1.469 1.292,1.917 0.427,0.448 10 false UDO+ 0.875,2.229 1.281,2.688 0.406,0.458 10 false UJSS

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the j2 radio and display receiver assembly connector.


b.

Disconnect the j1 No. 1 stereo jack adapter assembly connector.


c.
E360249C01
1.49,0.125 1.938,0.427 0.448,0.302 1.5,2.281 1.948,2.583 0.448,0.302 1.156,1.833 1.594,1.458 true 1.854,1.448 2.292,1.646 true 1.792,1.552 2.104,1.958 true 1.823,3.448 2.375,3.729 true 1.792,3.542 2.344,4.031 true 1.063,3.885 1.625,3.448 true 1.656,0.188 1.969,0.385 0.313,0.198 10 false j4 1.656,2.344 1.969,2.542 0.313,0.198 10 false j1 0.833,1.823 1.219,2.021 0.385,0.198 10 false US1+ 2.344,1.594 2.729,1.792 0.385,0.198 10 false US1- 2.146,1.917 2.615,2.198 0.469,0.281 10 false USG1 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 0.146,2.698 0.458,2.896 0.313,0.198 10 false *b 0.688,3.823 1.125,4.021 0.438,0.198 10 false UDO- 2.417,3.656 2.854,3.854 0.438,0.198 10 false UDO+ 2.375,4.031 2.854,4.302 0.479,0.271 10 false UJSS
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j2-2 (US1-) - j1-2 (UDO-) Always Below 1 Ω
j2-3 (US1+) - j1-3 (UDO+) Always Below 1 Ω
j2-5 (USG1) - j1-5 (UJSS) Always Below 1 Ω
j2-2 (US1-) - Body ground Always 10 kΩ or higher
j2-3 (US1+) - Body ground Always 10 kΩ or higher
j2-5 (USG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR