Home › Vehicle Exterior › LIGHTING (EXT) › HEIGHT CONTROL SENSOR
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0296124 HEIGHT CONTROL SENSOR G

LIGHTING (EXT)  HEIGHT CONTROL SENSOR  INSPECTION  


PROCEDURE

Hide 89408C 1.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

a.

Preparation for check

i.

Confirm the standard, high and low positions of the link that will be used in the following inspection.

·

The standard position is 58° from the maximum link angle (high) and 51° from the maximum link angle (low).

·

The high position (+33.85°) is 24.15° from the maximum link angle (high).

·

The low position (-33.85°) is 17.15° from the maximum link angle (low).


E351177C01
2.448,1.26 2.76,1.417 0.313,0.156 10 false *a 4.458,0.01 4.771,0.167 0.313,0.156 10 false *b 2.146,3.49 2.458,3.646 0.313,0.156 10 false *c 3.354,0.646 3.667,0.802 0.313,0.156 10 false *d 2.219,2.302 2.531,2.458 0.313,0.156 10 false *e 3.5,1.271 3.813,1.427 0.313,0.156 10 false *f 2.896,2.198 3.125,2.427 0.229,0.229 10 false *g
*a Standard Position *b Maximum Link Angle (Low)
*c Maximum Link Angle (High) *d 51°
*e 58° *f -33.85°
*g +33.85° - -



ii.

Connect 3 dry cell batteries (1.5 V) in series.

NOTICE:

Do not use rechargeable batteries as they may not output a voltage of 1.5 V.



iii.

Connect a positive (+) lead from the batteries to terminal 3 (SHB) and a negative (-) lead to terminal 1 (SHG).

E351178C01
5.354,2.281 4.865,2.656 true 5.635,2.281 5.635,2.75 true 5.917,2.281 6.375,2.708 true 4.656,1.281 4.969,1.438 0.313,0.156 10 false *a 2.521,0.042 2.833,0.198 0.313,0.156 10 false *b 0.531,1.271 0.844,1.427 0.313,0.156 10 false *c 0.208,3.5 0.521,3.656 0.313,0.156 10 false *d 1.333,0.719 1.646,0.875 0.313,0.156 10 false *e 0.323,2.323 0.635,2.479 0.313,0.156 10 false *f 4.708,2.667 5.083,2.833 0.375,0.167 10 false SHB 5.438,2.76 5.906,2.948 0.469,0.188 10 false SHRR 6.281,2.729 6.719,2.948 0.438,0.219 10 false SHG
*a Component without harness connected
(Rear Height Control Sensor Sub-assembly LH)
*b Low
*c Standard Position *d High
*e -33.85° *f +33.85°



iv.

Measure the voltage between terminals 2 (SHRR) and 1 (SHG) while slowly moving the link up and down.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (SHG) - 2 (SHRR) +33.85° (High) 4.15 V
1 (SHG) - 2 (SHRR) 0° (Standard position) 2.5 V
1 (SHG) - 2 (SHRR) -33.85° (Low) 1.04 V


If the result is not as specified, replace the rear height control sensor sub-assembly LH.