Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.10–2018.05
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK ECM


C367116N04
2.417,0.167 2.917,0.417 0.5,0.25 5.5,0.167 6,0.417 0.5,0.25 2.552,0.198 3.01,0.396 0.458,0.198 10 false C62 5.635,0.198 6.094,0.396 0.458,0.198 10 false A38

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
C62-34 (D)*1 - C62-53 (E1) Y - W-B D shift position signal Ignition switch to ON, shift lever in D 11 to 14 V
C62-34 (D)*1 - C62-53 (E1) Y - W-B D shift position signal Ignition switch to ON, shift lever not in D Below 1 V
A38-59 (S)*1 - C62-53 (E1) W - W-B M shift position signal Ignition switch to ON, shift lever in M 11 to 14 V
A38-59 (S)*1 - C62-53 (E1) W - W-B M shift position signal Ignition switch to ON, shift lever not in M Below 1 V
C62-119 (CLS)*2 - C62-87 (E2CL)*2 G - W Clutch pedal stroke sensor signal Ignition switch ON and clutch pedal fully released 0.2 to 1.5 V
Ignition switch ON and clutch pedal fully depressed 2.5 to 4.8 V
A38-9 (STP) - C62-53 (E1) R - W-B Stop light switch assembly signal Brake pedal depressed 11 to 14 V
A38-9 (STP) - C62-53 (E1) R - W-B Stop light switch assembly signal Brake pedal released Below 1 V
A38-43 (SFTD)*1 - C62-53 (E1) SB - W-B Down-shift position switch signal Ignition switch to ON, shift lever in M 11 to 14 V
A38-43 (SFTD)*1 - C62-53 (E1) SB - W-B Down-shift position switch signal Ignition switch to ON, shift lever in "-" Below 1 V
A38-42 (SFTU)*1 - C62-53 (E1) B - W-B Up-shift position switch signal Ignition switch to ON, shift lever in M 11 to 14 V
A38-42 (SFTU)*1 - C62-53 (E1) B - W-B Up-shift position switch signal Ignition switch to ON, shift lever in "+" Below 1 V
A38-55 (CCS) - C62-53 (E1) SB - W-B Cruise control main switch circuit Cruise control main switch (ON/OFF button) not pushed 1 MΩ or higher
A38-55 (CCS) - C62-53 (E1) SB - W-B Cruise control main switch circuit Cruise control main switch (ON/OFF button) pushed Below 2.5 Ω
A38-55 (CCS) - C62-53 (E1) SB - W-B Cruise control main switch circuit +RES switch ON 235 to 245 Ω
A38-55 (CCS) - C62-53 (E1) SB - W-B Cruise control main switch circuit -SET switch ON 617 to 643 Ω
A38-55 (CCS) - C62-53 (E1) SB - W-B Cruise control main switch circuit CANCEL switch ON 1509 to 1571 Ω
A38-10 (ST1-) - C62-53 (E1) G - W-B Stop light switch assembly signal Ignition switch to ON, brake pedal depressed Below 1 V
A38-10 (ST1-) - C62-53 (E1) G - W-B Stop light switch assembly signal Ignition switch to ON, brake pedal released 11 to 14 V

*1: for CVT

*2: for Manual Transaxle



CHECK FORWARD RECOGNITION CAMERA


C367139N01
3.333,0.083 3.833,0.333 0.5,0.25 3.5,0.125 3.813,0.323 0.313,0.198 10 false R5

NOTICE:

Do not apply excessive force to the connector. If a force of 10 kg or more is applied, the connector may be broken.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-8 (BZ) - R5-10 (GND) P - W-B*1
B - W-B*2
Pre-collision city buzzer output Ignition switch to ON, buzzer not sounding 11 to 14 V
Ignition switch to ON, buzzer sounding Below 1 V
R5-7 (IGB) - R5-10 (GND) B - W-B Power source Ignition switch to ON 11 to 14 V
Ignition switch off Below 1 V
R5-5 (CA1P) - R5-10 (GND) R - W-B CAN communication signal Ignition switch to ON Pulse generation
(See waveform 1)
R5-11 (CA1N) - R5-10 (GND) GR - W-B CAN communication signal Ignition switch to ON Pulse generation
(See waveform 2)
R5-6 (CANH) - R5-10 (GND) G - W-B CAN communication signal Ignition switch to ON Pulse generation
(See waveform 1)
R5-12 (CANL) - R5-10 (GND) R - W-B CAN communication signal Ignition switch to ON Pulse generation
(See waveform 2)
R5-3 (LKSW) - R5-10 (GND) SB - W-B*1
R - W-B*2
Steering pad switch assembly signal (distance control signal) Ignition switch to ON, steering pad switch assembly (distance control switch) off 4.75 to 5.25 V
Ignition switch to ON, steering pad switch assembly (distance control switch) on Below 1 V
R5-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

*1: for TMC Made

*2: for TMMT Made


a.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between R5-5 (CA1P) and R5-10 (GND)

·

Between R5-6 (CANH) and R5-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch to ON

HINT:

The waveform varies depending on the CAN communication signal.




b.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between R5-11 (CA1N) and R5-10 (GND)

·

Between R5-12 (CANL) and R5-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch to ON

HINT:

The waveform varies depending on the CAN communication signal.





CHECK MILLIMETER WAVE RADAR SENSOR


C367140N01
2.25,0.75 2.75,1 0.5,0.25 2.417,0.792 2.729,0.99 0.313,0.198 10 false A2

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A2-2 (CA2L) - A2-1 (SGND) GR - W-B CAN communication signal Ignition switch to ON Pulse generation
(See waveform 2)
A2-3 (CA2H) - A2-1 (SGND) G - W-B CAN communication signal Ignition switch to ON Pulse generation
(See waveform 1)
A2-5 (CA1P) - A2-1 (SGND) G - W-B CAN communication signal Ignition switch to ON Pulse generation
(See waveform 1)
A2-6 (CA1N) - A2-1 (SGND) R - W-B CAN communication signal Ignition switch to ON Pulse generation
(See waveform 2)
A2-8 (IGB) - A2-1 (SGND) B - W-B Power source Ignition switch to ON 11 to 14 V

a.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between A2-3 (CA2H) and A2-1 (SGND)

·

Between A2-5 (CA1P) and A2-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch to ON

HINT:

The waveform varies depending on the CAN communication signal.




b.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between A2-2 (CA2L) and A2-1 (SGND)

·

Between A2-6 (CA1N) and A2-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch to ON

HINT:

The waveform varies depending on the CAN communication signal.