When the system determines that the vehicle is driving straight ahead based on signals from the yaw rate sensor (airbag sensor assembly), etc., the millimeter wave radar sensor assembly performs self-diagnosis to check if the sensor beam axis is misaligned.
C1A11 is output when it is determined that the millimeter wave radar sensor assembly beam axis is misaligned.
If sensor beam axis adjustment is not performed after installing a new millimeter wave radar sensor assembly, C1A14 is output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A11 | Front Radar Sensor Incorrect Axial Gap | w/o Full-speed range following function:
·
When the vehicle is being driven at a speed of 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.3 seconds or more. w/ Full-speed range following function:
·
When the vehicle is being driven at a speed of 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.3 seconds or more. |
·
Millimeter wave radar sensor assembly |
| C1A14 | Front Radar Sensor Beam Axis Not Adjusted | w/o Full-speed range following function:
·
When the vehicle is being driven at a speed of 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, incompletion of the millimeter wave radar sensor beam axis alignment is detected for approximately 0.3 seconds or more. w/ Full-speed range following function:
·
When the vehicle is being driven at a speed of 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, incompletion of the millimeter wave radar sensor beam axis alignment is detected for approximately 0.3 seconds or more. |
·
Millimeter wave radar sensor assembly |
When replacing the millimeter wave radar sensor assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle, and as a result, a DTC may be stored.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Check if the stored DTCs are current DTCs.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Body Electrical / Radar Cruise 2 / Trouble Codes.
Click here
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Current DTC C1A11 is output | A |
| Current DTC C1A14 is output | B |
| History DTC C1A11 is output | C |
A
B
C
Check the operating conditions of the vehicle.
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.
| Result | Proceed to |
|---|---|
| Vehicle is not overloaded or being towed. | A |
| Vehicle is overloaded or being towed. | B |
A
B
Check the front and rear wheel alignment (toe).
for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels.
for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Turn the ignition switch to ON.
Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).
w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.
w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A11 is not output | A |
| DTC C1A11 is output | B |
A
B
Check that the bracket of the millimeter wave radar sensor assembly is not deformed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>INSTALLATION
If the bracket is deformed, replace the millimeter wave radar sensor assembly.
| Result | Proceed to |
|---|---|
| Bracket is not deformed | A |
| Bracket is deformed | B |
A
B
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Return the vehicle to normal operating conditions.
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Turn the ignition switch to ON.
Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).
w/ Full-speed range following function: Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.
w/o Full-speed range following function: Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A14 is not output | A |
| DTC C1A14 is output | B |
A
B
Check for DTCs related to misalignment of millimeter wave radar sensor assembly.
If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT