Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297891 FORWARD RECOGNITION CAMERA SYSTEM U

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  TERMINALS OF ECU  


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the R5 forward recognition camera connector.



a.

Disconnect the R5 forward recognition camera connector.

C356786E04
2.25,0.76 2.667,1 0.417,0.24 2.375,0.802 2.688,1 0.313,0.198 10 false R5


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-7 (IGB) - R5-10 (GND) B - W-B Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
R5-8 (BZ) - R5-10 (GND) P - W-B*1
B - W-B*2
Pre-collision city buzzer Ignition switch ON, pre-collision city buzzer not operating 11 to 14 V
Ignition switch ON, pre-collision city buzzer operating 0 to 1.5 V
R5-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

*1: for TMC Made

*2: for TMMT Made



c.

Reconnect the R5 forward recognition camera connector.

E256359C21
1.708,0.729 2.146,0.979 0.438,0.25 1.833,0.781 2.292,0.979 0.458,0.198 10 false R5 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Component with harness connected
(Forward Recognition Camera)
- -



d.

Check for pulses according to the value(s) in the table below.

HINT:

If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the forward recognition camera is suspected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-5 (CA1P) - R5-10 (GND) R - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
R5-11 (CA1N) - R5-10 (GND) GR - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)
R5-6 (CANH) - R5-10 (GND) G - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 1)
R5-12 (CANL) - R5-10 (GND) R - W-B CAN communication signal Ignition switch ON Pulse generation
(See waveform 2)

i.
A292386E11
1.344,1.917 2.313,2.146 0.969,0.229 10 false 10 μsec./DIV. 2.76,0.219 3.333,0.427 0.573,0.208 10 false 1 V/DIV. 3,1.406 3.365,1.583 0.365,0.177 10 false GND

Waveform 1

Item Content
Terminal Name Between R5-5 (CA1P) and R5-10 (GND)
Between R5-6 (CANH) and R5-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



ii.
A292387E14
3,1.375 3.344,1.573 0.344,0.198 10 false GND 2.781,0.26 3.417,0.458 0.635,0.198 10 false 1 V/DIV. 1.375,1.885 2.323,2.135 0.948,0.25 10 false 10 μsec./DIV.

Waveform 2

Item Content
Terminal Name Between R5-11 (CA1N) and R5-10 (GND)
Between R5-12 (CANL) and R5-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.