Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297891 FORWARD RECOGNITION CAMERA SYSTEM J

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the forward recognition camera.

WIRING DIAGRAM

C367129E01
2.323,0.698 3.292,0.917 0.969,0.219 10 false ECU-IG1 NO.4 1.813,1.052 2.708,1.427 0.896,0.375 10 false from Stop and Start System 3.938,0.438 4.167,0.615 0.229,0.177 10 false *2 3.938,1 4.167,1.177 0.229,0.177 10 false *1 5.219,0.458 5.375,0.625 0.156,0.167 10 false 7 5.458,0.542 5.865,0.729 0.406,0.188 10 false IGB 5.188,1.771 5.458,1.938 0.271,0.167 10 false 10 5.458,1.833 5.865,2.021 0.406,0.188 10 false GND 5.208,2.292 5.615,2.479 0.406,0.188 10 false R5 5.208,2.448 6.479,2.802 1.271,0.354 10 false Forward Recognition Camera 0.135,3 2.229,3.281 2.094,0.281 10 false *1: w/ Stop and Start System 0.135,3.323 2.229,3.604 2.094,0.281 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
A380142C43
1.521,0.167 1.875,0.417 0.354,0.25 0.917,1.542 1.26,1.385 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.604,0.208 1.917,0.406 0.313,0.198 10 false R5 0.646,1.469 1.104,1.667 0.458,0.198 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R5-7 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System



c.

Connect the forward recognition camera connector.


Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
A380142C44
1.521,0.167 1.875,0.417 0.354,0.25 1.698,1.802 1.792,1.438 true 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.615,0.219 1.927,0.417 0.313,0.198 10 false R5 1.563,1.823 2.021,2.021 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the forward recognition camera connector


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR