Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297891 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AA7  Skid Control Buzzer Circuit  


DESCRIPTION

The forward recognition camera operates the pre-collision warning by sending a buzzer request signal to the pre-collision city buzzer.

If the forward recognition camera detects a malfunction in the pre-collision city buzzer circuit, it will output DTC C1AA7.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA7 Skid Control Buzzer Circuit When the ignition switch is turned to ON and the pre-collision warning is operating, and one of the following conditions is met:
·

A buzzer request signal is sent to the pre-collision city buzzer but the buzzer does not sound for 1 second or more.

·

A buzzer request signal is not sent to the pre-collision city buzzer but the buzzer sounds for 1 second or more.

·

There is no buzzer sounding request and an open circuit is detected in the pre-collision city buzzer.


·

Pre-collision city buzzer

·

Forward recognition camera

·

Harness or connector



WIRING DIAGRAM

C367127E01
0.625,0.792 1.594,1.021 0.969,0.229 10 false ECU-IG1 NO.4 3.052,1 3.417,1.167 0.365,0.167 10 false F54 3.042,1.167 4.76,1.438 1.719,0.271 10 false Pre-Collision City Buzzer 3.146,0.573 3.333,0.76 0.188,0.188 10 false 2 3.333,0.667 3.688,0.885 0.354,0.219 10 false IG1 3.979,0.656 4.333,0.875 0.354,0.219 10 false BZ 4.25,0.573 4.438,0.76 0.188,0.188 10 false 1 5.104,0.573 5.292,0.76 0.188,0.188 10 false 8 5.281,0.646 5.635,0.865 0.354,0.219 10 false BZ 4.896,2.021 5.188,2.198 0.292,0.177 10 false R5 4.885,2.188 6.74,2.406 1.854,0.219 10 false Forward Recognition Camera 1.875,0.552 2.188,0.75 0.313,0.198 10 false *2 2.094,1.281 2.406,1.479 0.313,0.198 10 false *1 0.26,1.375 1.5,1.823 1.24,0.448 10 false from Stop and Start System 0.25,2.083 2.25,2.333 2,0.25 10 false *1: w/ Stop and Start System 0.25,2.417 2.25,2.667 2,0.25 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

w/o Stop and Start System: Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1AA7 to be stored if the DTC detection conditions are met.


Chassis > Front Recognition Camera > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Buzzer Pre-collision city buzzer ON / OFF Test possible with ignition switch ON, vehicle stopped
Chassis > Front Recognition Camera > Active Test
Tester Display
PCS Buzzer
50004 386 1

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA7 is not output A
DTC C1AA7 is output B



A

B

2.CHECK TERMINAL VOLTAGE
2.CHECK TERMINAL VOLTAGE
a.
B443157C09
1.5,0.177 1.906,0.417 0.406,0.24 1.99,1.333 2.5,1.156 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.583,0.219 1.896,0.406 0.313,0.188 10 false F54 2.552,1.063 3.01,1.26 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Pre-collision City Buzzer)


Disconnect the pre-collision city buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F54-2 (IG1) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
Ignition switch off Below 1 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



c.

Connect the pre-collision city buzzer connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER - BATTERY)

3.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
a.

Disconnect the F54 pre-collision city buzzer connector.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-1 (BZ) - R5-8 (BZ) Always Below 1 Ω
F54-1 (BZ) or R5-8 (BZ) - Body ground Always 10 kΩ or higher



d.

Connect the R5 forward recognition camera connector.


e.

Connect the F54 pre-collision city buzzer connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT PRE-COLLISION CITY BUZZER (CONFIRM BUZZER OPERATION)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY BUZZER - FORWARD RECOGNITION CAMERA)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
5.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1AA7 to be stored if the DTC detection conditions are met.


Chassis > Front Recognition Camera > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Buzzer Pre-collision city buzzer ON / OFF Test possible with ignition switch ON, vehicle stopped
Chassis > Front Recognition Camera > Active Test
Tester Display
PCS Buzzer
50004 386 1

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA7 is not output A
DTC C1AA7 is output B



A

END

B

6.INSPECT PRE-COLLISION CITY BUZZER (CONFIRM BUZZER OPERATION)
6.INSPECT PRE-COLLISION CITY BUZZER (CONFIRM BUZZER OPERATION)
a.

Turn the ignition switch to ON.


b.

Check if the pre-collision city buzzer is sounding.


Result:
Result Proceed to
The pre-collision city buzzer does not sound when the ignition switch is turned to ON A
The pre-collision city buzzer sounds continuously when the ignition switch is turned to ON B



A

7.INSPECT PRE-COLLISION CITY BUZZER (UNIT INSPECTION)

B

8.REPLACE PRE-COLLISION CITY BUZZER
7.INSPECT PRE-COLLISION CITY BUZZER (UNIT INSPECTION)


Result:
Result Proceed to
pre-collision city buzzer is abnormal A
Pre-collision city buzzer is normal B



A

8.REPLACE PRE-COLLISION CITY BUZZER

B

9.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
8.REPLACE PRE-COLLISION CITY BUZZER

NEXT

9.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
9.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Perform the Active Test according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1AA7 to be stored if the DTC detection conditions are met.


Chassis > Front Recognition Camera > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Buzzer Pre-collision city buzzer ON / OFF Test possible with ignition switch ON, vehicle stopped
Chassis > Front Recognition Camera > Active Test
Tester Display
PCS Buzzer
50004 386 1

c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AA7 is not output A
DTC C1AA7 is output B



A

END

B

REPLACE FORWARD RECOGNITION CAMERA