Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM (w/ Steering Control) › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297892 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  U0100  Lost Communication with ECM / PCM "A"  U0123  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication With Steering Angle Sensor Module  U0129  Lost Communication with Brake System Control Module  U0131  Lost Communication with Power Steering Control Module  U0142  Lost Communication with Body Control Module "B"  U0155  Lost Communication with Combination Meter  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

These DTCs are output when a communication malfunction occurs between the sensors and ECUs.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0100 Lost Communication with ECM / PCM "A" While the vehicle is being driven at 5 km/h or 3 mph or more, a communication error between the ECM and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

ECM

·

Forward recognition camera


U0123 Lost Communication with Yaw Rate Sensor Module 2 seconds after the ignition switch is turned ON, the vehicle is being driven at 1 km/h or 1 mph or more and a communication error between the yaw rate sensor and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Forward recognition camera


U0126 Lost Communication With Steering Angle Sensor Module 2 seconds after the ignition switch is turned ON, a communication error between the steering angle sensor and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Steering angle sensor (spiral cable sub-assembly)

·

Forward recognition camera


U0129 Lost Communication with Brake System Control Module 2 seconds after the ignition switch is turned ON, a communication error between the skid control ECU (brake actuator assembly) and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Skid control ECU (Brake actuator assembly)

·

Forward recognition camera


U0131 Lost Communication with Power Steering Control Module When the vehicle is being driven at a speed of 5 km/h (3 mph) or more 2 seconds after the ignition switch is turned ON, a communication error between the power steering ECU assembly and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Power steering ECU assembly

·

Forward recognition camera


U0142 Lost Communication with Body Control Module "B" 2 seconds after the ignition switch is turned ON, a communication error between the main body ECU (multiplex network body ECU) and the forward recognition camera is detected for approximately 5 seconds or more.
·

CAN communication system

·

Main body ECU (Multiplex network body ECU)

·

Forward recognition camera


U0155 Lost Communication with Combination Meter 2 seconds after the ignition switch is turned ON, a communication error between the combination meter assembly and the forward recognition camera is detected for approximately 50 seconds or more.
·

CAN communication system

·

Combination meter assembly

·

Forward recognition camera


U0235 Lost Communication with Cruise Control Front Distance Range Sensor When the vehicle is being driven at a speed of 5 km/h (3 mph) or more 2 seconds after the ignition switch is turned ON, a communication error between the millimeter wave radar sensor assembly and the forward recognition camera is detected for approximately 5 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Forward recognition camera



PROCEDURE

1.CHECK FOR DTCs
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.


e.

f.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the ignition switch is turned ON and wait 1 minute or more.

2.

Drive the vehicle at a speed of 1 km/h or 1 mph or more for 5 seconds or more.




g.

Enter the following menus: Chassis / LKA/LDA / Trouble Codes.


h.

Check the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM (w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC U0100, U0123, U0126, U0129, U0131, U0142, U0155 and U0235 are not output A
DTC U0100, U0123, U0126, U0129, U0131, U0142, U0155 or U0235 is output B



A

B