Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM (w/ Steering Control) › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297892 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the forward recognition camera.

WIRING DIAGRAM

C367125E01
1.865,0.917 3.021,1.135 1.156,0.219 10 false ECU-IG1 NO. 4 0.396,1.438 2.125,1.677 1.729,0.24 10 false for Stop and Start System 2.958,0.635 3.302,0.854 0.344,0.219 10 false *2 2.969,1.333 3.313,1.552 0.344,0.219 10 false *1 4.917,0.646 5.26,0.865 0.344,0.219 10 false 7 4.844,1.948 5.188,2.167 0.344,0.219 10 false 10 5.125,0.708 5.469,0.927 0.344,0.219 10 false IGB 5.115,2.01 5.458,2.229 0.344,0.219 10 false GND 5,2.5 5.344,2.719 0.344,0.219 10 false R5 4.99,2.677 6.313,3.25 1.323,0.573 10 false Forward Recognition Camera 0.208,2.771 2.198,3.125 1.99,0.354 10 false *1: w/ Stop and Start System 0.219,3.198 2.208,3.552 1.99,0.354 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)
a.
C367126C01
0.667,1.667 1,1.917 0.333,0.25 1.01,2.375 1.323,2.021 true 0.854,2.438 1.313,2.635 0.458,0.198 10 false IGB 0.74,1.698 1.042,1.917 0.302,0.219 10 false R5 0.146,0.104 0.604,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the R5 forward recognition camera connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R5-7 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
C367126C02
0.667,1.667 1,1.917 0.333,0.25 2.104,2.375 1.781,2.021 true 2.073,2.417 2.531,2.615 0.458,0.198 10 false GND 0.74,1.698 1.042,1.917 0.302,0.219 10 false R5 0.063,0.073 0.365,0.292 0.302,0.219 10 false *a
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the R5 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-10 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR