INSPECT ILLUMINATED ENTRY SYSTEM OPERATION
Perform this inspection with the customize parameters at the initial settings.
Perform this inspection with the door switch of the map light assembly on.
| Control | Condition | Lights that Operate |
|---|---|---|
| Actuation Area-linked*1 | With the engine switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off. | ·
Map Light Assembly ·
No. 1 Room Light Assembly |
| Door Lock/Unlock-linked | With the ignition switch off and all of the doors closed and locked, unlock either front door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off. | ·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*3 |
| Door Open/Close-linked | With the ignition switch off and all of the doors closed, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds. | ·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*3 |
| With the engine switch off and all of the doors closed, open either front door and check that the light that operates turns on. While the light that operates is on, close all of the doors and check that the light that operates turns off after approximately 40 seconds*1. | Engine Switch Illumination*1 | |
| With the ignition switch ACC or ON, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off. | ·
Map Light Assembly ·
No. 1 Room Light Assembly |
|
| Engine Switch-linked*1 | Turn the engine switch from on (ACC) or on (IG) to off and check that the lights that operate turn on for approximately 15 seconds and then turn off. | ·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2 |
| Ignition Switch-linked*2 | Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off. | ·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*3 |
| Shift position-linked*3, *4 | With the ignition switch turned to ACC or ON, move the shift lever from P to any position and check that the lights dim. While the lights are dim, move the shift lever to P and check that the lights return to full brightness. | ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*3 |
| Vehicle Speed-linked*3, *5 | With the ignition switch turned to ACC or ON, release the parking brake, drive the vehicle at least 3 km/h (1.9 mph), and check that the lights dim. While the lights are dim, stop the vehicle, apply the parking brake, and check that the lights return to full brightness. | ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*3 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*3 |
*1: w/ Entry and Start System
*2: w/o Entry and Start System
*3: w/ Door Ambient Illumination Light
*4: for CVT
*5: for Manual Transaxle
INSPECT BATTERY SAVING CONTROL OPERATION
The operations and conditions of this control are described below.
| Control | Condition | Lights that Operate |
|---|---|---|
| Basic operation | When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off.
|
·
Map Light Assembly ·
No. 1 Room Light Assembly ·
Engine Switch Illumination*1 ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2 |
| Interior light auto cut operation | When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off.
|
·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Luggage Compartment Light Assembly ·
Vanity Light Assembly |
*1: w/ Entry and Start System
*2: w/ Door Ambient Illumination Light