Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › 2016.10–2019.09
RM32H0E _59 Vehicle Exterior _060783 EXTERIOR PANELS / TRIM _0298064 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REMOVAL  


PROCEDURE

Hide 53141F 1.REMOVE RADIATOR COVER

a.
B453194

Remove the 4 clips and 2 hood bumper cushions.


b.
B454114

Disengage the guides to remove the radiator cover as shown in the illustration.


Hide 75602A 2.SEPARATE FRONT FENDER MOULDING SUB-ASSEMBLY LH

a.
B465601

Remove the 3 screws and 2 clips.


b.
B465602C01
0.417,0.76 0.885,1.031 true 2.5,0.708 2.708,0.885 0.208,0.177 10 true *a 0.229,0.667 0.438,0.844 0.208,0.177 10 false *1
*1 Pin Hold Clip
*a 90 deg


Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.

HINT:

Use the same procedure for the RH side and LH side.



c.
B465625C03
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull back the edge of the front fender liner LH and disengage the claws by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:
·

Do not apply excessive force when pulling back the front fender liner LH.

·

To avoid damaging the claws, do not forcibly pull the front fender moulding sub-assembly LH.




d.

Disengage the clips and separate the front fender moulding sub-assembly LH.


Hide 75601A 3.SEPARATE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 4.REMOVE FRONT BUMPER ASSEMBLY

a.
B454115C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front bumper assembly.

HINT:

Use the same procedure for the RH side and LH side.



b.
B465603

Remove the 6 screws.


c.
B454116C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claws as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



d.

w/ Fog Light:

i.
B465606C01
0.302,2.844 0.552,3.052 0.25,0.208 12 true *A 1.885,2.854 2.135,3.063 0.25,0.208 12 true *B
*A w/ Fog Light
*B w/o Fog Light
V113147

Remove in this Direction


Pull back the side of the front bumper assembly and disconnect the connector.

NOTICE:

Do not apply excessive force when pulling back the front bumper assembly.


HINT:

Use the same procedure for the RH side and LH side.




e.

w/o Fog Light:

i.

Pull back the side of the front bumper assembly and disconnect the connector from the fog light cover.

NOTICE:

Do not apply excessive force when pulling back the front bumper assembly.


HINT:

Use the same procedure for the RH side and LH side.




f.

w/ Headlight Cleaner System:

i.
B454121

Disconnect the washer hose and drain the washer fluid.

HINT:

Use a container to collect the washer fluid.




g.
B454118C01
0.969,1.323 0.563,1.073 true 1.281,0.5 0.938,0.385 true 0.271,0.938 0.51,1.146 0.24,0.208 10 true *B 1.313,0.427 1.552,0.635 0.24,0.208 10 true *A
*A w/ Toyota Safety Sense
*B w/ TOYOTA Parking Assist-sensor System


w/ TOYOTA Parking Assist-sensor System:

i.

Disconnect the connector.



h.

w/ Toyota Safety Sense:

i.

Disconnect the connector.



i.
B453494

Remove the 3 bolts.


j.
B465632C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claw to remove front bumper assembly as shown in the illustration.