Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING(for Rear)
RM32H0E _59 Vehicle Exterior _060783 EXTERIOR PANELS / TRIM _0298084 WHEEL OPENING MOULDING(for Rear) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Rear)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75696 1.INSTALL NO. 1 BODY OUTSIDE MOULDING PAD

HINT:

When installing the No. 1 body outside moulding pad, heat the quarter outside moulding using a heat light.


CAUTION:
·
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



Standard:
Item Temperature
Quarter Outside Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the quarter outside moulding excessively.


a.

Clean the No. 1 body outside moulding pad installation surface with a non-residue solvent.


b.

Apply primer to the No. 1 body outside moulding pad installation area on the quarter outside moulding.

NOTICE:

Apply primer evenly so that there are no uncoated areas.



c.

Remove the peeling paper on a new No. 1 body outside moulding pad while making sure not to touch the adhesive surface.


d.
B458760C01
1.906,4.01 2.635,4.333 2.635,4.333 1.885,3.927 true 1.458,1.323 0.594,0.979 0.594,0.979 1.385,1.229 true 2.5,3.771 1.583,3 1.583,3 2.417,3.417 true 1.604,0.677 1.083,0.75 1.083,0.75 1.396,0.594 true 0.375,0.854 0.688,1.01 0.313,0.156 10 false *1 1.49,0.406 1.802,0.563 0.313,0.156 10 false *a 1.167,1.313 1.479,1.469 0.313,0.156 10 false *b 2.688,4.354 3,4.51 0.313,0.156 10 false *1 0.906,0.646 1.219,0.802 0.313,0.156 10 false *1 1.406,2.896 1.719,3.052 0.313,0.156 10 false *1 1.615,3.771 1.927,3.927 0.313,0.156 10 false *d 2.563,3.469 2.875,3.625 0.313,0.156 10 false *c
*1 Mark-off Line
*a 5.0 mm (0.197 in.)
*b 2.0 mm (0.0787 in.)
*c 8.0 mm (0.315 in.)
*d 1.6 mm (0.0630 in.)


Install a No. 1 body outside moulding pad in the position shown in the illustration.

NOTICE:
·

Press the double-sided tape on the No. 1 body outside moulding pad firmly to attach.

·

After the primer dries (3 minutes or more), install the No. 1 body outside moulding pad.

·

After applying primer, reapply primer after 24 hours elapse.