Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM32H0E _59 Vehicle Exterior _060316 WIPER / WASHER _0298086 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to hold the front wiper arm while lifting it as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade.


PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E356867C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push the windshield wiper motor assembly in the direction indicated by the arrow (1), then move the windshield wiper motor assembly in the direction indicated by the arrow (2) shown in the illustration to temporarily install it to the windshield wiper link assembly.


b.

Install the windshield wiper motor assembly with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.
E356868C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the pivot of the windshield wiper motor assembly.


d.
E356869C01
2.417,1.667 1.938,1.104 true 2.49,1.563 2.802,1.719 0.313,0.156 10 false *a
*a Pivot of Windshield Wiper Motor Assembly


Connect the No. 1 windshield wiper link rod to the pivot of the windshield wiper motor assembly.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.

Connect the connector.


b.
E356870C02
0.594,0.396 0.708,0.521 true 2.74,0.698 2.917,0.583 true 0.375,0.271 0.563,0.469 0.188,0.198 10 true *a 2.969,0.469 3.156,0.667 0.188,0.198 10 true *a
*a Motor Grommet


Engage the motor grommet as shown in the illustration.

NOTICE:

Be careful not to damage the windshield glass when installing the windshield wiper motor and link assembly.



c.

Install the windshield wiper motor and link assembly with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 55708 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Engage the guides as shown in the illustration.

E356871C01
0,0 0,0 false
V113147

Install in this Direction - -


NOTICE:

When installing the cowl top ventilator louver sub-assembly, it may contact the brake master cylinder reservoir filler cap assembly and cause it to fall off. Check the installation condition of the brake master cylinder reservoir filler cap assembly after installing the cowl top ventilator louver sub-assembly.



b.

Engage the guides to install the cowl top ventilator louver sub-assembly as shown in the illustration.

E356872C01
0,0 0,0 false
V113147

Install in this Direction - -



c.

Install the 2 clips.


Hide 75534 4.INSTALL WINDSHIELD OUTSIDE MOULDING LH

a.
E356873C01
1.625,0.698 1.781,0.896 0.156,0.198 10 true 1 1.76,1.552 1.917,1.75 0.156,0.198 10 true 2 2.104,1.75 2.26,1.948 0.156,0.198 10 true 3
V113147

Install in this Direction


Engage the clip and claws to install the windshield moulding outside LH as shown in the illustration.


Hide 75533 5.INSTALL WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

When reusing the front wiper arm and blade assembly RH:

i.
E356874C02
1.719,1.24 2.385,0.448 true 1.865,2.927 2.583,2.604 true 2.458,0.344 2.771,0.5 0.313,0.156 10 false *a 2.646,2.521 2.958,2.677 0.313,0.156 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper motor and link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.

Turn the ignition switch to ON.


d.

Operate the windshield wiper motor assembly and stop the windshield wiper motor and link assembly at the automatic stop position.


e.

Turn the ignition switch off.


f.
E356851C04
1.198,2.833 1.594,2.615 true 1.646,2.51 1.833,2.698 0.188,0.188 10 true *a 0.896,2.51 1.042,2.698 0.146,0.188 10 true A 0.833,2.823 0.969,3.01 0.135,0.188 10 true A
*a Alignment Mark


Install the front wiper arm and blade assembly RH with the nut to the position as shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 7.5 mm (0.295 in.)



Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.

When reusing the front wiper arm and blade assembly LH:

i.
E356875C01
1.719,1.24 2.25,0.677 true 1.833,2.938 2.646,2.552 true 2.313,0.573 2.5,0.781 0.188,0.208 10 false *a 2.708,2.458 2.896,2.667 0.188,0.208 10 false *a
*a Serration


Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




b.

When reusing the windshield wiper motor and link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E356850C04
1.552,2.75 1.813,2.51 true 1.875,2.396 2.042,2.583 0.167,0.188 10 true *a 1.188,2.51 1.354,2.698 0.167,0.188 10 true A 1.188,2.833 1.354,3.021 0.167,0.188 10 true A
*a Alignment Mark


Install the front wiper arm and blade assembly LH with the nut to the position as shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 7.5 mm (0.295 in.)



d.

Turn the ignition switch to ON.


e.

Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not contact the vehicle body.


f.

Turn the ignition switch off.


g.

Lift each wiper arm twice after the wipers stop and check the wiper set position.


Hide 85292B 8.INSTALL FRONT WIPER ARM HEAD CAP

a.
E356876C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front wiper arm head cap as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.