Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM › 2016.10–2019.09
RM32H0E _52 Drivetrain _059725 GF1A TRANSFER / 4WD / AWD _0298220 DYNAMIC TORQUE CONTROL AWD SYSTEM D

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (When Using GTS)


a.

Check the DTCs.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Read the DTCs following the prompts on the GTS screen. Enter the following menus: Chassis / Four Wheel Drive / Trouble Codes.

Chassis > Four Wheel Drive > Trouble Codes
50001 118




CLEAR DTC (When Using GTS)


a.

Clear the DTCs.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Operate the GTS to clear the DTCs. Enter the following menus: Chassis / Four Wheel Drive / Trouble Codes.

Chassis > Four Wheel Drive > Clear DTCs
50002 118

v.

According to the display on the GTS, select the trouble code data display with the clear button.




CHECK DTC (When Using SST Check Wire)


a.
C368526C02
0.094,1.083 0.594,1.333 0.5,0.25 1.583,0.917 1.917,0.417 true 2,1.833 1.76,1.479 true 0.167,0.167 0.583,0.5 0.417,0.333 10 false *a 1.99,0.333 2.385,0.583 0.396,0.25 10 false CG 0.229,1.083 0.625,1.333 0.396,0.25 10 false F41 1.948,1.844 2.344,2.094 0.396,0.25 10 false TC
*a Front view of DLC3


Check the DTCs.

i.

Using SST, connect terminals TC (13) and CG (4) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Read the DTCs displayed on the multi-information display.

HINT:
·

If no DTCs are displayed on the multi-information display, perform the relevant troubleshooting procedures. The relevant troubleshooting procedures are in the sections listed in the table below.

·

"DIAG AWD" is displayed on the multi-information display, and the 4WD ECU assembly checks the system for malfunctions.

·

If the dynamic torque control AWD system is normal, "DIAG AWD FF" will be displayed on the multi-information display (normal system code).

·

If the dynamic torque control AWD system is not normal, "DIAG AWD XX (DTC)" will be displayed on the multi-information display.

·

DTCs are explained in "DIAGNOSTIC TROUBLE CODE CHART".

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

Section Title See Procedure
AWD Warning Light does not Come ON (Click here)
TC and CG Terminal Circuit (Click here)






CLEAR DTC (When Using SST Check Wire)


a.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the ignition switch to ON.


c.
C108863

Clear the DTCs stored in the 4WD ECU assembly by depressing the brake pedal 8 times or more within 5 seconds.


d.

Check that the warning displays "DIAG AWD FF".


e.

Remove SST from the terminals of the DLC3.


f.

Turn the ignition switch off.

HINT:

DTCs cannot be cleared by disconnecting the cable from the negative (-) battery terminal or removing the ECU-IG1 NO. 2 fuse.