Home › Power Source / Network › 8NR-FTS (BATTERY / CHARGING) › GENERATOR (for VALEO Made)
RM32H0E _57 Power Source / Network _060209 8NR-FTS BATTERY / CHARGING _0295244 GENERATOR(for VALEO Made) A

8NR-FTS BATTERY / CHARGING  GENERATOR(for VALEO Made)  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A386476

Using a screwdriver, remove the generator pulley cap from the generator pulley with clutch.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
A392489C01
1.396,0.458 1.854,0.458 true 2.563,1.073 2.646,1.25 false 1.948,2.313 2.25,2.313 false 1.177,0.333 1.49,0.531 0.313,0.198 10 false *1 2.688,1.188 3.031,1.365 0.344,0.177 10 false SST 2.302,2.219 2.646,2.396 0.344,0.177 10 false SST
*1 Generator Pulley with Clutch


Fit SST to the generator pulley with clutch.

SST
09820-30010  


c.
A392490C01
1.542,0.521 1.979,0.875 true 2.854,0.583 3.042,0.802 false 2.427,1.094 2.615,1.313 false 1.927,2.188 2.208,2.063 false 2.24,2.406 2.573,2.406 false 1.354,0.406 1.667,0.563 0.313,0.156 10 false *a 2.667,0.49 2.979,0.646 0.313,0.156 10 false *b 2.656,1.229 3.115,1.427 0.458,0.198 10 false SST 2.25,1.969 2.708,2.167 0.458,0.198 10 false SST 2.635,2.323 2.948,2.479 0.313,0.156 10 false *b
*a Rotor Shaft
*b T45 "TORX" Socket Wrench


Fit a T45 "TORX" socket wrench into the rotor shaft end.


d.
A392491C01
1.063,1.5 0.75,1.375 false 2.75,0.958 2.427,1.052 false 2.448,0.813 2.125,0.948 true 2.792,0.854 3.104,1.01 0.313,0.156 10 false *a 0.573,1.281 0.885,1.438 0.313,0.156 10 false *b 1.125,1.979 1.313,2.135 0.188,0.156 10 true *c 2.49,0.708 2.823,0.875 0.333,0.167 10 false SST
*a T45 "TORX" Socket Wrench
*b Turn
*c Hold


Loosen the generator pulley with clutch by turning the T45 "TORX" socket wrench as shown in the illustration.

NOTICE:
·

Check that the generator assembly is secured in the vise tightly.

·

Hold SST tightly during the operation.




e.

Remove SST and the T45 "TORX" socket wrench from the generator pulley with clutch.


f.

Remove the generator pulley with clutch from the rotor shaft.


g.

Remove the generator assembly from the vise.