Home › Power Source / Network › 8NR-FTS (BATTERY / CHARGING) › GENERATOR (for VALEO Made)
RM32H0E _57 Power Source / Network _060209 8NR-FTS BATTERY / CHARGING _0295244 GENERATOR(for VALEO Made) A

8NR-FTS BATTERY / CHARGING  GENERATOR(for VALEO Made)  REASSEMBLY  


PROCEDURE

Hide 27415 1.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Temporarily install the generator pulley with clutch to the rotor shaft.


c.
A392489C02
1.417,0.448 1.844,0.448 true 2.563,1.063 2.656,1.24 false 1.938,2.313 2.219,2.313 false 1.219,0.323 1.531,0.521 0.313,0.198 10 false *1 2.708,1.167 3.042,1.354 0.333,0.188 10 false SST 2.292,2.229 2.625,2.417 0.333,0.188 10 false SST
*1 Generator Pulley with Clutch


Fit SST to the generator pulley with clutch.

SST
09820-30010  


d.
A392490C02
1.969,0.875 1.563,0.531 true 3.021,0.802 2.76,0.531 false 2.583,1.26 2.406,1.094 false 2.104,2.083 1.823,2.198 true 2.479,2.406 2.24,2.406 false 1.385,0.427 1.698,0.625 0.313,0.198 10 false *a 2.583,0.438 2.896,0.635 0.313,0.198 10 false *b 2.635,1.198 3.031,1.406 0.396,0.208 10 false SST 2.146,2 2.542,2.208 0.396,0.208 10 false SST 2.531,2.313 2.844,2.51 0.313,0.198 10 false *b
*a Rotor Shaft
*b T45 "TORX" Socket Wrench


Fit a T45 "TORX" socket wrench into the rotor shaft end.


e.
A392452C01
2.667,0.75 3,0.75 false 0.635,1.729 0.99,2.031 false 2.24,1.75 2.875,1.75 true 3.073,0.646 3.323,0.896 0.25,0.25 10 false *c 1.948,2.156 2.146,2.333 0.198,0.177 10 true *a 0.458,1.625 0.708,1.875 0.25,0.25 10 false *b 2.927,1.667 3.292,1.875 0.365,0.208 10 false SST
*a Torque Wrench Fulcrum Length
*b Turn
*c Hold


Tighten the generator pulley with clutch by turning SST as shown in the illustration.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 400 mm (1.312 ft.)): 74.4 N*m (759 kgf*cm, 55 ft.*lbf)




f.

Remove SST and the T45 "TORX" socket wrench from the generator pulley with clutch.


g.

Check that the generator pulley with clutch rotates smoothly.


h.

Remove the generator assembly from the vise.


Hide 27416 2.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.