Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0298358 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Image from Camera for Rear View Monitor is Abnormal  


DESCRIPTION

The display signal of the rear television camera assembly is transmitted to the radio and display receiver assembly.

WIRING DIAGRAM

E360114E03
5.406,2.813 7.125,3.49 1.719,0.677 10 false Radio and Display Receiver Assembly 5.427,2.604 5.885,2.802 0.458,0.198 10 false F50 5.667,2.177 6.125,2.375 0.458,0.198 10 false CGND 5.688,1.708 6.146,1.906 0.458,0.198 10 false V- 5.677,1.25 6.135,1.448 0.458,0.198 10 false V+ 5.677,0.75 6.135,0.948 0.458,0.198 10 false CA+ 1.135,0.76 1.594,0.958 0.458,0.198 10 false CB+ 1.135,1.208 1.594,1.406 0.458,0.198 10 false CV+ 1.167,1.688 1.625,1.885 0.458,0.198 10 false CV- 1.021,2.177 1.479,2.375 0.458,0.198 10 false CGND 0.156,2.604 0.615,2.802 0.458,0.198 10 false S11 0.156,2.802 2.594,3.073 2.438,0.271 10 false Rear Television Camera Assembly 0.167,3.417 1.854,3.615 1.688,0.198 10 false *: Shielded 2.156,2.344 2.427,2.542 0.271,0.198 10 false * 3.302,2.333 3.573,2.531 0.271,0.198 10 false * 4.469,2.344 4.74,2.542 0.271,0.198 10 false * 5.417,2.073 5.729,2.271 0.313,0.198 10 false 23 5.427,1.594 5.74,1.792 0.313,0.198 10 false 24 5.427,1.115 5.74,1.313 0.313,0.198 10 false 12 5.427,0.677 5.74,0.875 0.313,0.198 10 false 11 1.521,2.073 1.833,2.271 0.313,0.198 10 false 5 1.51,1.604 1.823,1.802 0.313,0.198 10 false 2 1.51,1.135 1.823,1.333 0.313,0.198 10 false 3 1.51,0.677 1.823,0.875 0.313,0.198 10 false 6

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F50 radio and display receiver assembly connector.


b.

Disconnect the S11 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F50-11 (CA+) - S11-6 (CB+) Always Below 1 Ω
F50-12 (V+) - S11-3 (CV+) Always Below 1 Ω
F50-24 (V-) - S11-2 (CV-) Always Below 1 Ω
F50-23 (CGND) - S11-5 (CGND) Always Below 1 Ω
F50-11 (CA+) or S11-6 (CB+) - Body ground Always 10 kΩ or higher
F50-12 (V+) or S11-3 (CV+) - Body ground Always 10 kΩ or higher
F50-24 (V-) or S11-2 (CV-) - Body ground Always 10 kΩ or higher
F50-23 (CGND) or S11-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E280624C32
1.458,0.323 2.01,0.583 0.552,0.26 1.094,1.031 0.813,0.729 0.813,0.729 0.469,0.729 true 1.094,1.271 1.021,1.927 1.021,1.927 0.75,1.927 true 0.938,1.271 0.875,1.635 0.875,1.635 0.698,1.635 true 1.604,0.354 2.219,0.552 0.615,0.198 10 false F50 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.417,1.552 0.729,1.75 0.313,0.198 10 false V- 0.135,0.635 0.521,0.833 0.385,0.198 10 false CA+ 0.281,1.844 0.771,2.052 0.49,0.208 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F50-23 (CGND) - Body ground Always Below 1 Ω
F50-24 (V-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F50-11 (CA+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

3.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Remove the radio and display receiver assembly with the connector connected.

E280623C21
1.25,0.531 1.75,0.802 0.5,0.271 3.146,2.292 3.344,2.292 3.344,2.292 3.5,1.792 false 3.885,2.281 3.729,2.281 3.729,2.281 3.594,1.729 false 6.052,2.188 5.896,2.188 5.896,2.188 5.76,1.635 false 5.302,2.177 5.5,2.177 5.5,2.177 5.656,1.677 false 0.646,2.083 0.813,2.083 0.813,2.083 0.917,1.458 true 0.417,0.969 0.552,0.969 0.552,0.969 0.781,1.24 true 0.073,0.167 0.385,0.365 0.313,0.198 10 false *a 3.042,0.188 3.354,0.385 0.313,0.198 10 false *b 5.177,0.167 5.49,0.365 0.313,0.198 10 false *c 2.917,2.188 3.229,2.385 0.313,0.198 10 false *d 5.115,2.094 5.427,2.292 0.313,0.198 10 false *d 3.979,2.198 4.292,2.396 0.313,0.198 10 false *e 6.104,2.104 6.417,2.302 0.313,0.198 10 false *e 4.969,1.354 5.396,1.552 0.427,0.198 10 false GND 2.823,1.344 3.25,1.542 0.427,0.198 10 false GND 0.083,0.906 0.51,1.104 0.427,0.198 10 false V+ 0.188,2 0.646,2.26 0.458,0.26 10 false CGND 1.396,0.583 1.823,0.781 0.427,0.198 10 false F50
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) F50-12 (V+) - F50-23 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



Result:
Proceed to
OK
NG



OK

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Replace the radio and display receiver assembly with a new or normally functioning one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Check if the same malfunction recurs when the rear view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (RADIO AND DISPLAY RECEIVER ASSEMBLY WAS DEFECTIVE)

NG