Home › General › MAINTENANCE › GF1A TRANSFER OIL
RM32H0E _V1 General _059503 MAINTENANCE _0298705 GF1A TRANSFER OIL A

MAINTENANCE  GF1A TRANSFER OIL  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN TRANSFER OIL

a.

Stop the vehicle on a level surface.


b.
C277146C01
1.521,0.594 1.927,0.417 1.927,0.417 2.063,0.417 true 1.698,1.646 1.896,1.896 1.896,1.896 2.052,1.896 true 2.156,0.333 2.469,0.531 0.313,0.198 10 *1 2.156,1.781 2.469,1.979 0.313,0.198 10 *2
*1 Transfer Filler Plug
*2 Transfer Drain Plug


Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket.


c.

Using a 10 mm hexagon socket wrench, remove the transfer drain plug and gasket and drain the transfer oil.


d.

Using a 10 mm hexagon socket wrench, install a new gasket and the drain plug.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 2.ADD TRANSFER OIL

a.

Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket.


b.

Add transfer oil.

Oil grade:

Toyota Genuine Differential gear oil LT SAE 75W-85 API GL-5 or equivalent


Viscosity:

SAE 75W-85



c.
C278961C01
2.667,0.854 2.979,1.052 0.313,0.198 10 false *a
*a 0 to 5.0 mm (0 to 0.196 in.)


Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.196 in.) from the bottom lip of the transfer filler plug hole.

NOTICE:
·

When adding oil, pour it slowly.

·

Add oil a little at a time, waiting several minutes between each addition of oil.

·

Too much or too little oil will lead to transfer problems.



Standard Capacity:

0.40 to 0.50 liters (0.43 to 0.52 US qts, 0.36 to 0.44 Imp. qts)



d.

Wait approximately 5 minutes and check that the oil level has not changed.


e.
C368139C03
0.625,4.469 0.375,4.219 false 1.167,4.25 0.917,4 false 1.75,4.313 1.5,4.063 false 0.646,4.448 0.958,4.604 0.313,0.156 10 false *a 1.781,4.313 2.094,4.469 0.313,0.156 10 false *b 1.208,4.25 1.521,4.406 0.313,0.156 10 false *c 2.094,3.281 2.406,3.438 0.313,0.156 10 false *d
*a 10 mm Straight Hexagon Wrench
*b 12 mm Hexagon Socket Wrench
*c 10 x 12 mm Long Offset Wrench
*d Fulcrum Length


Using a 10 mm straight hexagon wrench, 12 mm hexagon socket wrench and 10 x 12 mm long offset wrench, install a new gasket into the transfer filler plug and then install the transfer filler plug.

Torque:
Specified tightening torque : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

After adding oil, drive the vehicle and recheck the oil level (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

This torque value is effective when offset wrench is straight to a torque wrench.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a long offset wrench (fulcrum length of 189.75 mm (7.47 in.)) + torque wrench (fulcrum length of 255 mm (10.04 in.)): 22.4 N*m (228 kgf*cm, 17 ft.*lbf)