Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Millimeter Wave Radar Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Millimeter Wave Radar Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Front Radar" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Front Radar" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Front Radar" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Millimeter Wave Radar Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Millimeter wave radar sensor assembly branch line or connector

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

C369869E02
0.083,1.729 2.292,2.042 2.208,0.313 10 false No. 1 CAN Junction Connector 0.083,1.563 0.792,1.75 0.708,0.188 10 false F112 1.646,0.531 2.354,0.719 0.708,0.188 10 false 3 1.646,1.063 2.354,1.25 0.708,0.188 10 false 14 5.583,1.063 5.854,1.26 0.271,0.198 10 false 2 5.583,0.531 5.823,0.719 0.24,0.188 10 false 3 5.583,2.125 5.844,2.313 0.26,0.188 10 false 8 5.583,3 5.885,3.188 0.302,0.188 10 false 1 5.813,0.625 6.344,0.854 0.531,0.229 10 false CA2H 5.813,1.167 6.365,1.385 0.552,0.219 10 false CA2L 5.813,2.229 6.219,2.417 0.406,0.188 10 false IGB 5.813,3.094 6.438,3.313 0.625,0.219 10 false SGND 4.167,2.365 5.281,2.573 1.115,0.208 10 false ECU-IG1 NO. 3 5.521,3.656 6.948,4.094 1.427,0.438 10 false Millimeter Wave Radar Sensor Assembly 5.521,3.49 6.146,3.708 0.625,0.219 10 false A2 2.083,2.229 3.781,2.563 1.698,0.333 10 false from IG1-NO. 1 Relay*1 1.396,2.698 3.896,2.927 2.5,0.229 10 false from Engine Stop and Start ECU*2 0.49,3.583 2.99,3.813 2.5,0.229 10 false *1: w/o Stop and Start System 0.49,3.917 2.99,4.146 2.5,0.229 10 false *2: w/ Stop and Start System 4.938,2.125 5.198,2.313 0.26,0.188 10 false *1 5.396,2.458 5.656,2.646 0.26,0.188 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the cruise control main switch on and then drive the vehicle at a speed of 40 km/h (25 mph) or more for approximately 10 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.


c.
C346951C09
1.49,0.156 1.854,0.365 0.365,0.208 1.552,1.073 1.042,0.427 true 1.833,1.083 2.354,0.406 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.604,0.167 1.844,0.396 0.24,0.229 10 false A2 2.438,0.302 2.906,0.521 0.469,0.219 10 false CA2H 0.604,0.313 1.052,0.531 0.448,0.219 10 false CA2L
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-3 (CA2H) - A2-2 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346951C10
1.49,0.156 1.854,0.365 0.365,0.208 0.927,0.531 1.375,1.073 true 2.458,1.927 2.01,1.365 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.167 1.833,0.375 0.25,0.208 10 false A2 2.552,1.844 2.844,2.031 0.292,0.188 10 false IGB 0.448,0.427 0.896,0.583 0.448,0.156 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-1 (SGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A2-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (except IGB circuit) (w/ Stop and Start System)
NG (for IGB circuit) (w/ Stop and Start System) C



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

C

GO TO STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)