Use these procedures to troubleshoot the pre-collision system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
| Pre-collision System Customer Problem Analysis | Vehicle Brought to Workshop | ||||||
|---|---|---|---|---|---|---|---|
| Year | Month | Day | |||||
| Dealer name | Person in charge at headquarters | Telephone number | |||||
| Shop name | Person in charge at shop | ||||||
| Frame type | Frame No. | First Registered Year | Total distance traveled | ||||
| Customer Concerns (Include details) | Does not operate | ||||||
| Operates abnormally | |||||||
| Date of malfunction occurrence (Since when) | Year | Month | Day | Approx. Time | |||
| Date of last inspection | Year | Month | Day | ||||
| Frequency of problem symptoms | Once / Occasionally (times per day, times per month) / Every time certain conditions are met ( ) | ||||||
| Weather | Sunny / Cloudy / Rain / Snow (Amount of snowfall cm) / Other ( ) | Vehicle speed | Approximately ( ) km/h | ||||
| Place | Prefecture
(Attach a map if possible) |
||||||
| Driving path (where vehicle turned, where driver attempted to drive to, etc.)
* Describe the conditions immediately after the occurrence in as much detail as possible. |
Conditions of Occurrence Diagram
|
||||||
0.771,1.104 0.313,0.458
0.313,0.458 0.719,0.458
true
1.365,1.042 1.646,0.76
1.646,0.76 1.99,0.76
true
0.406,1.854 0.198,1.854
0.198,1.854 1.063,1.177
true
1.875,1.271 2.083,1.438
true
1.563,1.469 1.719,1.885
1.719,1.885 1.927,1.885
true
0.75,0.063 1.99,0.26
1.24,0.198
10
false
Diagram Example
0.781,0.385 3.229,0.583
2.448,0.198
10
false
Oncoming vehicle
2.042,0.677 3.208,1
1.167,0.323
10
false
Stopped vehicle
0.479,1.792 1.406,2.01
0.927,0.219
10
false
Occurred here
1.979,1.823 3.052,2.021
1.073,0.198
10
false
Vehicle
2.135,1.354 3.427,1.604
1.292,0.25
10
false
Approximately ( ) m
|
|||||||
| Surrounding road conditions
Describe whether there were any billboards, metal objects on the road (manholes), guardrails, pipes, cat's eyes, gate bars, etc. |
|||||||
| Urban area / Suburbs / Highway / Other ( ) | Road surface conditions | Temperature | About °C ( °F) | ||||
| Direction of travel | Straight / Right turn / Left turn / Right curve / Left curve | Snow wall(s) | Y / N | ||||
| Driving lane | Number of lanes on one side (lanes) / ( ) lane(s) from left | Backlighting | Y / N | ||||
| Condition of external area around detection sensor | No foreign matter / Foreign matter (water, snow, ice, other) | ||||||
| Additional information about condition of vehicle exterior (other than above) | |||||||
| DTC | First Time (when vehicle brought to workshop) | ||||||
| Second Time (after clearing DTC) | |||||||
| Status of operation switch | Pre-collision system cancel switch | Far / Medium / Near / OFF | VSC OFF switch | ON / OFF | |||
| Serial number of main part
* Fill in when removing, installing or replacing part |
Forward recognition camera | ||||||
| Describe the items to the right in as much detail as possible. | Driver operation | Accelerator pedal operated / Brake pedal operated / Steering wheel operated | Time elapsed after engine was started | Approximately ( ) minutes | |||
| Tire pressure inspection result | Front: LH ( ) kPa RH ( ) kPa Standard ( ) kPa | ||||||
| Rear: LH ( ) kPa RH ( ) kPa Standard ( ) kPa | |||||||
| Sensor optical axis inspection result | Forward recognition camera | Accident history | Y / N | ||||
| Millimeter wave radar sensor assembly | Accident history | Y / N | |||||
| Vehicle modified | Y ( ) / N | ||||||
| Items installed or attached around windshield glass | Drive recorder* / Radar detector / Navigation unit (genuine/non-genuine) / ETC / Charms or toys / Other:
*: As information regarding the item is important for the investigation, make sure to obtain the item if permission is given by the customer. |
||||||
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Adjust the reflector height.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Place the reflector.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Turn the cruise control main switch on.
Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.
Check the amount of misalignment and make a note.
| Tester Display |
|---|
| Front Beam Axis Misalignment Reading |
Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.
Check the amount of offset and make a note.
| Tester Display |
|---|
| Front Beam Axis Offset Reading |
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check if the CAN communication system is functioning normally.
Refer to CAN Bus Check in CAN Communication System.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
CAN communication system is functioning normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the condition of the warning lights on the combination meter assembly.
| Result | Proceed to |
|---|---|
| Only the PCS warning light is blinking | A |
| The PCS warning light is not blinking | |
| The PCS warning light and other warning lights are illuminated or blinking | B |
A
B
Check if a pre-collision system warning message is displayed on the multi-information display in the combination meter assembly.
| Result | Proceed to |
|---|---|
| "Pre-Collision System Malfunction Visit Your Dealer" is displayed (for TFT Display Type) | A |
| "PRE-COLLISION SYSTEM MALFUNCTION VISIT YOUR DEALER" is displayed (for Dot Display Type) | |
| Any of the following messages is displayed (for TFT Display Type):
·
"Pre-Collision System Unavailable" ·
"Pre-Collision System Unavailable Clean Sensor" ·
"Front Camera Unavailable" ·
"Front Camera Vision Blocked. Clean and Demist Windshield" |
B |
| Any of the following messages is displayed (for Dot Display Type):
·
"PRE-COLLISION SYSTEM UNAVAILABLE" ·
"PRE-COLLISION SYSTEM UNAVAILABLE CLEAN SENSOR" ·
"FRONT CAMERA UNAVAILABLE" ·
"FRONT CAMERA VISION BLOCKED CLEAN AND DEMIST WINDSHIELD" |
|
| Warning message is not displayed | C |
A
B
C
Refer to DTC Check / Clear.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Check for DTCs and note any codes that are output.
Clear the DTCs.
Recheck for DTCs.
Attempt to duplicate the malfunction and check if the DTCs are output again.
| Result | Proceed to |
|---|---|
| Malfunction is duplicated but DTCs are not output | A |
| Malfunction cannot be duplicated and DTCs are not output | B |
| DTCs are output | C |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
C
Refer to Problem Symptoms Table.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Terminals of ECU
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>TERMINALS OF ECU
Data List / Active Test
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST
| Proceed to |
|---|
| NEXT |
NEXT
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT