Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2020.08
RM32H0E _58 Vehicle Interior _059622 PRE-COLLISION _0298842 PRE-COLLISION SYSTEM D

PRE-COLLISION  PRE-COLLISION SYSTEM  UTILITY  


NOTICE:

When replacing a millimeter wave radar sensor assembly, replace it with a new one.

If the millimeter wave radar sensor assembly has been replaced or removed/installed, be sure to perform Front Beam Axis Adjustment. If not performed, DTC C1A14 will be stored when the system is turned on.


Control Mode


HINT:
·

This mode is used to check the operation of the pre-collision system when reproducing situations when the pre-collision system operated unnecessarily.

·

Operating the pre-collision brake assist control or pre-collision brake control when reproducing problem symptoms may lead to a dangerous situation. To avoid this, do not attempt to operate the pre-collision brake control, only operate the pre-collision alarm control (buzzer and warning message) when reproducing the problem symptoms.

PCS Control Operated Buzzer Sound
Pre-collision alarm control Intermittent (Long)
Pre-collision brake assist control Intermittent (Short)
Pre-collision brake control Continuous



a.

Connect the GTS to the DLC3.


b.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Control Mode.


c.

Perform Control Mode according to the display on the GTS.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Control Mode
50005 220 2395


Front Beam Axis Adjustment


HINT:

Front Beam Axis Adjustment of the millimeter wave radar sensor assembly is performed using the GTS.


a.

Connect the GTS to the DLC3.


b.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Adjustment.


c.

Perform Front Beam Axis Adjustment according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Adjustment
50005 220 4404


Front Beam Axis Misalignment Reading


HINT:

The amount of misalignment of the millimeter wave radar sensor assembly can be checked using the GTS.


a.

Connect the GTS to the DLC3.


b.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.


c.

Perform Front Beam Axis Misalignment Reading according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 220 4405


Front Beam Axis Offset Reading


HINT:

The offset of the millimeter wave radar sensor assembly can be checked using the GTS.


a.

Connect the GTS to the DLC3.


b.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.


c.

Perform Front Beam Axis Offset Reading according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Offset Reading
50005 220 4406


History Clear


HINT:

If the status of any history data is "ON", clear the history data.


a.

Connect the GTS to the DLC3.


b.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / History Clear.


c.

Perform History Clear according to the display on the GTS.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
History Clear
50005 220 4412