Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2020.08
RM32H0E _58 Vehicle Interior _059622 PRE-COLLISION _0298842 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  C1AA8  Front Camera Module Incorrect Axial Gap  C1AA9  Front Camera Module Beam Axis Not Adjusted  


DESCRIPTION

If the millimeter wave radar sensor assembly detects that the forward recognition camera beam has an axis misalignment, DTC C1AA8 is output.

Also if Forward Recognition Axis Adjustment has not been performed or did not complete normally after the forward recognition camera was replaced with a new one, DTC C1AA9 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA8 Front Camera Module Incorrect Axial Gap When the pre-collision system is operating, the millimeter wave radar sensor assembly continuously receives a signal indicating that the beam axis of the forward recognition camera is misaligned for 0.3 seconds or more.
·

Forward recognition camera system

·

Millimeter wave radar sensor assembly


C1AA9 Front Camera Module Beam Axis Not Adjusted When the pre-collision system is operating, the millimeter wave radar sensor assembly detects that Forward Recognition Axis Adjustment has not been completed for 0.3 seconds or more.
·

Forward recognition camera system

·

Millimeter wave radar sensor assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

The pre-collision system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
HINT:

Pre-collision system DTC C1AA8 and/or C1AA9 may be stored due to a malfunction in the forward recognition camera system. Therefore, it is necessary to check for and troubleshoot forward recognition camera system DTCs first.


a.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
Forward recognition camera system DTCs are not output A
Forward recognition camera system DTCs are output B



A

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)

B

2.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1AA8 and/or C1AA9 is not output A
DTC C1AA8 and/or C1AA9 is output B



A

B

3.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
4.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1AA8 and/or C1AA9 is not output A
DTC C1AA8 and/or C1AA9 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA