Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059622 PRE-COLLISION _0298842 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
U1002 Lost Communication with Gateway Module When the ignition switch to ON, a communication error between the forward recognition camera and millimeter wave radar sensor assembly is detected for approximately 0.3 seconds.
·

CAN bus sab line or connector

·

Forward recognition camera system

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

C360449E02
0.073,1.01 2.417,1.25 2.344,0.24 10 false from Engine Stop and Start ECU*1 0.729,1.542 3.063,1.781 2.333,0.24 10 false from IG1-NO. 1 Relay*2 2.542,1.708 3.958,1.875 1.417,0.167 10 false ECU-IG1 NO. 3*2 4.542,0.917 4.708,1.083 0.167,0.167 10 false 8 4.542,1.573 4.708,1.74 0.167,0.167 10 false 1 6.219,0.917 6.385,1.083 0.167,0.167 10 false 5 6.219,1.583 6.385,1.75 0.167,0.167 10 false 6 4.74,0.927 5.073,1.094 0.333,0.167 10 false IGB 4.75,1.688 5.25,1.854 0.5,0.167 10 false SGND 5.719,1.021 6.219,1.188 0.5,0.167 10 false CA1P 5.729,1.667 6.229,1.833 0.5,0.167 10 false CA1N 4.76,2.083 5.26,2.25 0.5,0.167 10 false A2 4.75,2.25 6.167,2.667 1.417,0.417 10 false Millimeter Wave Radar Sensor Assembly 6.25,3.125 6.417,3.292 0.167,0.167 10 false 6 6.219,3.802 6.552,3.969 0.333,0.167 10 false 12 4.552,3.125 4.885,3.292 0.333,0.167 10 false 7 4.5,3.792 4.833,3.958 0.333,0.167 10 false 10 4.75,3.146 5.167,3.313 0.417,0.167 10 false IGB 5.708,3.24 6.292,3.406 0.583,0.167 10 false CANH 5.719,3.885 6.302,4.052 0.583,0.167 10 false CANL 4.75,3.896 5.333,4.063 0.583,0.167 10 false GND 4.677,4.323 5.26,4.49 0.583,0.167 10 false R5 4.656,4.5 6.573,4.75 1.917,0.25 10 false Forward Recognition Camera 2.531,3.917 3.948,4.083 1.417,0.167 10 false ECU-IG1 NO. 4*2 0.698,3.75 2.281,3.99 1.583,0.24 10 false from IG1-NO. 1 Relay*2 0.094,3.229 2.677,3.479 2.583,0.25 10 false from Engine Stop and Start ECU*1 0.26,4.844 2.844,5.094 2.583,0.25 10 false *1: w/ Stop and Start System 0.26,5.188 2.844,5.438 2.583,0.25 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECUs and sensors to communicate using the CAN communication system. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U023A and/or U1002 and other DTCs are output A
Only DTC U023A and/or U1002 is output B



A

B

2.CHECK FOR OPEN IN CAN BUS SAB LINES (FORWARD RECOGNITION CAMERA)
2.CHECK FOR OPEN IN CAN BUS SAB LINES (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C351772C35
1.5,0.167 2,0.417 0.5,0.25 1.781,1.823 2.073,1.458 true 2.156,1.125 2.448,0.76 true 2.469,0.625 2.927,0.823 0.458,0.198 10 false CANH 1.656,0.198 2.115,0.396 0.458,0.198 10 false R5 0.156,0.156 0.615,0.354 0.458,0.198 10 false *a 1.615,1.865 2.073,2.063 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-6 (CANH) - R5-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



d.

Connect the forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE (FORWARD RECOGNITION CAMERA))

NG

REPAIR OR REPLACE CAN BUS SAB LINE OR CONNECTOR (FORWARD RECOGNITION CAMERA - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE (FORWARD RECOGNITION CAMERA))
a.
C351772C36
1.458,0.167 1.958,0.417 0.5,0.25 0.979,1.781 1.271,1.417 true 0.844,1.813 1.302,2.01 0.458,0.198 10 false IGB 1.615,0.198 1.875,0.417 0.26,0.219 10 false R5 0.156,0.156 0.615,0.354 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R5-7 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System



d.

Connect the forward recognition camera connector.


Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

C

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
C351772C37
1.469,0.177 1.969,0.427 0.5,0.25 2.104,1.813 1.802,1.469 true 1.635,0.208 2.094,0.406 0.458,0.198 10 false R5 0.156,0.156 0.615,0.354 0.458,0.198 10 false *a 2.021,1.844 2.479,2.042 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY))
a.
E361286C01
1.448,0.125 1.948,0.375 0.5,0.25 1.958,1.229 2.5,1.594 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 2.573,1.51 2.906,1.698 0.333,0.188 10 false IGB 1.615,0.167 1.927,0.323 0.313,0.156 10 false A2
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A2-8 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System



c.

Connect the millimeter wave radar sensor assembly connector.


Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

6.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

C

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.
E361286C02
1.438,0.146 1.938,0.396 0.5,0.25 0.771,1.469 1.396,1.01 true 0.323,1.375 0.76,1.573 0.438,0.198 10 false SGND 1.615,0.177 2.052,0.375 0.438,0.198 10 false A2
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-1 (SGND) - Body ground Always Below 1 Ω



c.

Connect the millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
8.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U023A is not output A
DTC U023A is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

9.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
9.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC (PRE-COLLISION SYSTEM)
10.CLEAR DTC (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Clear DTCs
50002 220

Result:
Proceed to
NEXT



NEXT

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)