Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059622 PRE-COLLISION _0298842 PRE-COLLISION SYSTEM J

PRE-COLLISION  PRE-COLLISION SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to the millimeter wave radar sensor assembly when the ignition switch to ON.

WIRING DIAGRAM

C360451E02
0.25,1.188 2.5,1.438 2.25,0.25 10 false from Engine Stop and Start ECU*1 0.865,1.729 2.615,1.979 1.75,0.25 10 false from IG1-NO. 1 Relay*2 2.677,1.885 4.344,2.052 1.667,0.167 10 false ECU-IG1 NO. 3*2 0.25,2.604 2.583,2.854 2.333,0.25 10 false *1: w/ Stop and Start System 0.271,3.021 2.604,3.271 2.333,0.25 10 false *2: w/o Stop and Start System 4.719,1.083 4.969,1.25 0.25,0.167 10 false 8 4.708,1.75 4.958,1.917 0.25,0.167 10 false 1 4.938,1.083 5.354,1.25 0.417,0.167 10 false IGB 4.927,1.854 5.51,2.021 0.583,0.167 10 false SGND 4.969,2.271 5.552,2.438 0.583,0.167 10 false A2 4.948,2.438 6.365,2.938 1.417,0.5 10 false Millimeter Wave Radar Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Stop and Start System:

As the millimeter wave radar sensor assembly is supplied power from the engine stop and start ECU, make sure that the stop and start system is not malfunctioning before performing the following inspection procedure.

·

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (IGB VOLTAGE)
a.
E361286C03
1.448,0.125 1.948,0.375 0.5,0.25 1.958,1.229 2.5,1.594 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 2.573,1.51 2.906,1.698 0.333,0.188 10 false IGB 1.615,0.167 1.927,0.323 0.313,0.156 10 false A2
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A2-8 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2


*1: w/o Stop and Start System

*2: w/ Stop and Start System



d.

Turn the ignition switch off.


e.

Reconnect the millimeter wave radar sensor assembly connector.


Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

C

GO TO STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.
E361286C04
1.448,0.125 1.948,0.375 0.5,0.25 1.406,1.073 0.927,1.542 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.479,1.458 0.917,1.667 0.438,0.208 10 false SGND 1.615,0.167 1.927,0.323 0.313,0.156 10 false A2
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2-1 (SGND) - Body ground Always Below 1 Ω



c.

Connect the millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR