Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299013 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A7  Open in Inside Luggage Compartment Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (inside luggage compartment). For the No. 3 indoor electrical key antenna assembly (inside luggage compartment) to detect when the electrical key transmitter sub-assembly is in the cabin, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A7 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A7 Open in Inside Luggage Compartment Electrical Key Oscillator Circuit An open is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

No. 3 indoor electrical key antenna assembly (inside luggage compartment)

·

Harness or connector


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in luggage compartment:
·

Power source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC No. Data List and Active Test
B27A7 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B463969E11
0.094,2.646 2.969,3.156 2.875,0.51 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment) 5.104,2.531 6.635,3.063 1.531,0.531 10 false Certification ECU (Smart Key ECU Assembly) 0.094,2.49 0.427,2.698 0.333,0.208 10 false M37 4.917,0.854 5.271,1.031 0.354,0.177 10 false M67 4.927,2 5.281,2.177 0.354,0.177 10 false M67 6.521,2 6.875,2.177 0.354,0.177 10 false F1 5.313,0.771 5.771,0.948 0.458,0.177 10 false CLG7 5.302,1.917 5.76,2.094 0.458,0.177 10 false CG7B 5.823,1.406 6.177,1.583 0.354,0.177 10 false IC 6.25,2 6.458,2.167 0.208,0.167 10 false E 1.219,0.74 1.74,0.917 0.521,0.177 10 false ANTE7 1.271,1.917 1.74,2.094 0.469,0.177 10 false CLGB 1.76,0.75 1.938,0.927 0.177,0.177 10 false 1 1.781,1.917 1.958,2.094 0.177,0.177 10 false 3 4.969,0.656 5.198,0.823 0.229,0.167 10 false 11 4.969,1.813 5.208,1.979 0.24,0.167 10 false 10 6.531,1.792 6.708,1.969 0.177,0.177 10 false 18

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (inside luggage compartment).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))
a.

Disconnect the M67 and F1 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the M37 No. 3 indoor electrical key antenna assembly (inside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M67-11 (CLG7) - M37-1 (ANTE7) Always Below 1 Ω
M67-10 (CG7B) - M37-3 (CLGB) Always Below 1 Ω
F1-18 (E) - Body ground Always Below 1 Ω
M67-11 (CLG7) or M37-1 (ANTE7) - Body ground Always 10 kΩ or higher
M67-10 (CG7B) or M37-3 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the M67 and F1 certification ECU (smart key ECU assembly) connectors.


Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))
B416826C17
4.563,0.375 4.948,0.583 0.385,0.208 3.26,0.375 3.646,0.583 0.385,0.208 3.208,2.146 3.438,1.188 true 3.688,2.135 3.521,1.198 true 5.542,2.167 5.198,1.302 true 4.677,0.396 4.99,0.594 0.313,0.198 10 false F1 3.052,2.167 3.49,2.385 0.438,0.219 10 false CLG7 3.542,2.167 3.979,2.385 0.438,0.219 10 false CG7B 5.531,2.198 5.813,2.427 0.281,0.229 10 false E 0.292,0.198 0.604,0.396 0.313,0.198 10 false *a 1.01,2.802 1.323,3 0.313,0.198 10 false *b 0.771,3.677 1.083,3.875 0.313,0.198 10 false GND 1.521,4.375 1.833,4.573 0.313,0.198 10 false *c 2.354,4.385 2.667,4.583 0.313,0.198 10 false *d 3.323,0.385 3.75,0.604 0.427,0.219 10 false M67
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c For 30 seconds after any door closed *d After 30 seconds or more have elapsed since any door closed


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
M67-11 (CLG7) - F1-18 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
M67-10 (CG7B) - F1-18 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage compartment) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A7 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)