Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299014 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2284  Brake Signal Malfunction  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2284 Brake Signal Malfunction The brake signal sent via direct line and the brake signal sent via CAN communication do not match. (1-trip detection logic*)
·

AM2 fuse

·

STOP fuse

·

Stop light switch assembly

·

Vehicle stability control system

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Connect the cable to the negative (-) battery terminal, release the brake pedal and wait at least 20 seconds. Then depress the brake pedal for 20 seconds or more.



*: Only detected while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the key indicator display is not displayed on the multi-information display). However, the engine can be started by turning the engine switch on (ACC) and then pressing and holding it.
·

If there is a malfunction when the brake signal sent via direct line is on, the engine can be started by pressing the engine switch with the brake pedal released.

·

If there is a malfunction when the brake signal sent via direct line is off, the engine cannot be started by pressing the engine switch with the brake pedal depressed.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2284
Power Source Control
·

Stop Light Switch1


ABS/VSC/TRC/EPB
·

Stop Light SW



WIRING DIAGRAM

E352012E03
3.99,3.01 5.552,3.542 1.563,0.531 10 false Certification ECU (Smart Key ECU Assembly) 0.208,0.792 2.042,0.99 1.833,0.198 10 false from Battery 0.198,1.573 2.031,1.771 1.833,0.198 10 false from Battery 2.302,0.948 2.76,1.135 0.458,0.188 10 false AM2 1.625,1.719 2.083,1.906 0.458,0.188 10 false STOP 2.24,1.479 2.698,1.667 0.458,0.188 10 false 7 2.25,1.76 2.708,1.948 0.458,0.188 10 false 2 2.5,1.583 2.958,1.771 0.458,0.188 10 false B 2.479,1.865 2.938,2.052 0.458,0.188 10 false GND 2.906,1.688 3.365,1.875 0.458,0.188 10 false IC 3.198,1.479 3.656,1.667 0.458,0.188 10 false L 3.427,1.479 3.885,1.667 0.458,0.188 10 false 3 2.333,2.188 2.792,2.375 0.458,0.188 10 false A45 2.333,2.354 3.479,2.75 1.146,0.396 10 false Stop Light Switch Assembly 3.958,1.583 4.417,1.771 0.458,0.188 10 false M67 4,2.438 4.458,2.625 0.458,0.188 10 false F1 4,2.25 4.458,2.438 0.458,0.188 10 false 18 4.021,1.396 4.479,1.583 0.458,0.188 10 false 25 4,0.802 4.458,0.99 0.458,0.188 10 false F1 4.042,0.615 4.5,0.802 0.458,0.188 10 false 4 4.333,0.802 4.792,0.99 0.458,0.188 10 false +B 4.333,1.479 4.792,1.667 0.458,0.188 10 false STP1 4.333,2.438 4.792,2.625 0.458,0.188 10 false E 4.958,1.677 5.417,1.865 0.458,0.188 10 false IC 6.021,2.156 7.115,2.854 1.094,0.698 10 false Skid Control ECU (Brake Actuator Assembly) 0.635,3.25 2.625,3.448 1.99,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

GO TO VEHICLE STABILITY CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the M67 certification ECU (smart Key ECU assembly) connector.


b.

Disconnect the A45 stop light switch assembly connector.


c.
B331566C83
0.323,0.958 0.823,1.208 0.5,0.25 1.177,1.833 1.344,1.333 true 2.604,1.833 2.469,1.344 true 1.771,1.833 1.625,1.333 true 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 1.021,1.844 1.417,2.063 0.396,0.219 10 false GND 0.458,0.99 0.854,1.208 0.396,0.219 10 false A45 2.573,1.844 2.969,2.063 0.396,0.219 10 false B 1.76,1.844 2.156,2.063 0.396,0.219 10 false L
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-7 (B) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M67-25 (STP1) - A45-3 (L) Always Below 1 Ω
A45-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the M67 certification ECU (smart Key ECU assembly) connectors.


b.

Reconnect the A45 stop light switch assembly connector.


c.
B424431C09
1.448,0.167 1.948,0.417 0.5,0.25 1.094,2 1.344,1.167 true 0.167,0.25 0.479,0.448 0.313,0.198 10 false *a 1.573,0.188 1.969,0.396 0.396,0.208 10 false M67 0.698,1.896 1.26,2.146 0.563,0.25 10 false STP1
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M67-25 (STP1) - Body ground Brake pedal released → depressed 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY