Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/ Entry and Start System)
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299015 IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a history DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short When either of the following conditions is met (1-trip detection logic*1):
·

The transponder key amplifier coil built into the engine switch is open (determined by communication with certification ECU (smart key ECU assembly)).

·

The transponder key amplifier coil built into the engine switch is shorted (determined by communication with certification ECU (smart key ECU assembly)).


·

Engine switch

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC output confirmation operation:

With the shift lever in P*2 and the electrical key transmitter sub-assembly held near the engine switch, an engine start operation is performed by pressing and holding the engine switch when the transmitter battery is depleted.



*1: Only output while a malfunction is present.

*2: for CVT


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Always ○ ○
Malfunction Status The transponder key amplifier coil built into the engine switch is open (determined by communication with certification ECU (smart key ECU assembly)). ○ -
The transponder key amplifier coil built into the engine switch is shorted (determined by communication with certification ECU (smart key ECU assembly)). - ○
Detection Time - -
Number of Trips 1 trip 1 trip

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started when transmitter battery is depleted by holding electrical key transmitter sub-assembly near engine switch and pressing and holding engine switch with shift lever in P*1 -

*1: for CVT


Related Data List and Active Test
DTC No. Data List and Active Test
B2784 -

WIRING DIAGRAM

E305785E36
1.531,0.792 2.052,1.25 0.521,0.458 10 false VC5 1.906,0.677 2.427,1.135 0.521,0.458 10 false 10 1.479,1.313 2,1.771 0.521,0.458 10 false TXCT 1.406,1.729 1.927,2.188 0.521,0.458 10 false CODE 1.938,1.208 2.458,1.667 0.521,0.458 10 false 7 1.938,1.719 2.458,2.177 0.521,0.458 10 false 8 1.938,2.229 2.458,2.688 0.521,0.458 10 false 6 1.417,2.24 1.938,2.698 0.521,0.458 10 false AGND 0.573,3.042 0.917,3.219 0.344,0.177 10 false F59 0.573,3.208 2.01,3.417 1.438,0.208 10 false Engine Switch 5.031,0.677 5.552,1.135 0.521,0.458 10 false 7 5.042,1.198 5.563,1.656 0.521,0.458 10 false 5 5.042,1.708 5.563,2.167 0.521,0.458 10 false 6 4.99,2.219 5.51,2.677 0.521,0.458 10 false 11 5.688,0.302 6.208,0.76 0.521,0.458 10 false 5 V 5.292,3.031 5.813,3.49 0.521,0.458 10 false F1 5.302,3.188 6.833,3.552 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.26,0.688 5.781,1.146 0.521,0.458 10 false VC5 5.26,1.198 5.781,1.656 0.521,0.458 10 false TXCT 5.25,1.708 5.771,2.167 0.521,0.458 10 false CODE 5.25,2.219 5.771,2.677 0.521,0.458 10 false AGND 6.156,1.531 6.677,1.99 0.521,0.458 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B2784 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK ENGINE SWITCH (OUTPUT)
3.CHECK ENGINE SWITCH (OUTPUT)
a.

Using an oscilloscope, check the waveform.

B363541C34
1.458,0.958 1.813,1.177 0.354,0.219 2.229,2.875 1.885,2.135 true 1.344,2.885 1.635,2.135 true 0.74,1.083 1.052,1.24 0.313,0.156 10 false *a 3.385,0.281 3.698,0.438 0.313,0.156 10 false *b 3.406,2.052 3.719,2.208 0.313,0.156 10 false *c 6.49,1.333 7.031,1.563 0.542,0.229 10 false GND 6.49,3.115 7.031,3.344 0.542,0.229 10 false GND 2.083,2.958 2.625,3.188 0.542,0.229 10 false AGND 1.104,2.958 1.646,3.188 0.542,0.229 10 false CODE 1.521,0.979 2.063,1.208 0.542,0.229 10 false F59
*a Component with harness connected
(Engine Switch)
*b Waveform
*c Waveform (detail) - -


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
F59-8 (CODE) - F59-6 (AGND) Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch* 1 V/DIV., 20 ms./DIV. Pulse generation
(See waveform)
2 V/DIV., 100 μs./DIV. Pulse generation
(See waveform (detail))


*: Remove the transmitter battery before performing this inspection.


OK:

The waveform is similar to that shown in the illustration



Result:
Proceed to Proceed to
OK A
NG (for 8NR-FTS with LHD) B
NG (for 8NR-FTS with RHD) C
NG (for 3ZR-FAE) D



A

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

D

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B2784 is not output.



Result:
Proceed to Proceed to
OK A
NG (for 8NR-FTS with LHD) B
NG (for 8NR-FTS with RHD) C
NG (for 3ZR-FAE) D



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

C

D