Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Entry and Start System) › 2016.10–2018.05
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299017 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short Any of the following conditions is met:
·

The antenna coil in the transponder key coil is open (1 trip detection logic*1).

·

The antenna coil in the transponder key coil is shorted (1 trip detection logic*1).


·

Wire harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.



*1: Only output while a malfunction is present.


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Always ○ ○
Malfunction Status The antenna coil in the transponder key coil is open. ○ -
The antenna coil in the transponder key coil is shorted. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2784 Antenna Coil Status

WIRING DIAGRAM

C352175E06
1.281,0.625 1.896,0.823 0.615,0.198 10 false ANT1 1.281,1.771 1.896,1.969 0.615,0.198 10 false ANT2 5.333,0.625 5.948,0.823 0.615,0.198 10 false ANT1 5.333,1.771 5.948,1.969 0.615,0.198 10 false ANT2 5.104,0.625 5.26,0.823 0.156,0.198 10 false 4 5.031,1.771 5.385,1.969 0.354,0.198 10 false 15 1.771,1.771 2.125,1.969 0.354,0.198 10 false 5 1.771,0.625 2.125,0.823 0.354,0.198 10 false 1 5.958,1.167 6.573,1.365 0.615,0.198 10 false IC 5.135,2.396 5.75,2.594 0.615,0.198 10 false F22 5.146,2.563 6.542,3.167 1.396,0.604 10 false Transponder Key ECU Assembly 0.521,2.396 1.135,2.594 0.615,0.198 10 false F79 0.531,2.563 2.01,2.844 1.479,0.281 10 false Transponder Key Coil

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
B2784 is output B



A

B

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the transponder key coil.


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
B2784 is output B



A

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

B

6.CHECK TRANSPONDER KEY COIL (OUTPUT)
6.CHECK TRANSPONDER KEY COIL (OUTPUT)
a.

Using an oscilloscope, check the waveform.

B329326C30
3.417,0.073 3.74,0.292 0.323,0.219 4.115,1.167 3.813,0.792 true 3.177,1.167 3.323,0.771 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1,1.448 1.313,1.646 0.313,0.198 10 false *b 1,3.542 1.313,3.74 0.313,0.198 10 false *c 6.542,2.479 7.083,2.781 0.542,0.302 10 false GND 6.552,4.552 7.094,4.854 0.542,0.302 10 false GND 3.979,1.188 4.521,1.49 0.542,0.302 10 false ANT1 3.031,1.188 3.573,1.49 0.542,0.302 10 false ANT2 3.458,0.094 3.917,0.292 0.458,0.198 10 false F79
*a Component with harness connected
(Transponder Key Coil)
*b Waveform 1
*c Waveform 2 - -


Waveform 1
Item Content
Tester Connection F79-1 (ANT1) ←→ Body ground
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder

Waveform 2
Item Content
Tester Connection F79-5 (ANT2) ←→ Body ground
Tool Setting 20 V/DIV., 2 s./DIV.
Tool Setting Within 3 seconds of inserting key into ignition key cylinder

OK:

Waveform is similar to that shown in the illustration



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL AND BODY GROUND)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL AND BODY GROUND)
a.

Disconnect the F22 transponder key ECU assembly connector.


b.

Disconnect the F79 transponder key coil connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F22-4 (ANT1) - F79-1 (ANT1) Always Below 1 Ω
F22-15 (ANT2) - F79-5 (ANT2) Always Below 1 Ω
F22-4 (ANT1) - Body ground Always 10 kΩ or higher
F79-1 (ANT1) - Body ground Always 10 kΩ or higher
F22-15 (ANT2) - Body ground Always 10 kΩ or higher
F79-5 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Result Proceed to
B2784 is not output A
B2784 is output B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B