Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Entry and Start System) › 2016.10–2018.05
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299017 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B2796  No Communication in Immobiliser System  


DESCRIPTION

This DTC is stored when a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2796 No Communication in Immobiliser System The key ID code cannot be transmitted to the transponder key ECU assembly (1 trip detection logic*).
·

Key

·

Wire harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2796 -

WIRING DIAGRAM

C352175E07
1.281,0.625 1.896,0.823 0.615,0.198 10 false ANT1 1.281,1.771 1.896,1.969 0.615,0.198 10 false ANT2 5.333,0.625 5.948,0.823 0.615,0.198 10 false ANT1 5.333,1.771 5.948,1.969 0.615,0.198 10 false ANT2 5.104,0.625 5.26,0.823 0.156,0.198 10 false 4 5.031,1.771 5.385,1.969 0.354,0.198 10 false 15 1.771,1.771 2.125,1.969 0.354,0.198 10 false 5 1.771,0.625 2.125,0.823 0.354,0.198 10 false 1 5.958,1.167 6.573,1.365 0.615,0.198 10 false IC 5.135,2.396 5.75,2.594 0.615,0.198 10 false F22 5.146,2.563 6.542,3.167 1.396,0.604 10 false Transponder Key ECU Assembly 0.521,2.396 1.135,2.594 0.615,0.198 10 false F79 0.531,2.563 2.01,2.844 1.479,0.281 10 false Transponder Key Coil

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Insert and remove each registered key one at a time, and check for DTCs each time.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2796 is not output.



Result:
Result Proceed to
B2796 is not output A
DTC B2796 is output for all of the keys B
DTC B2796 is output for any of the keys C



A

B

3.REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

6.REPLACE KEY
3.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2796 is not output.



Result:
Result Proceed to
B2796 is not output A
B2796 is output B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

REPLACE KEY THAT DTC IS OUTPUT

6.REPLACE KEY
a.

Replace the key for which the DTC was stored.

NOTICE:

Key ID code registration is necessary when replacing the key.

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2796 is not output.



Result:
Result Proceed to
B2796 is not output A
B2796 is output B



A

END (KEY WAS DEFECTIVE)

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY