Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Entry and Start System)
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299017 IMMOBILISER SYSTEM(w/o Entry and Start System) Y

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use this procedure to troubleshoot the immobiliser system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:



What Vehicle model, system name
When Date, time, occurrence frequency
Where Whether the problem occurs at a specific location
Under what conditions? Whether the doors were locked or unlocked, whether the ignition switch was on, whether the engine was running.
How did it happen? Problem symptoms

Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CRANK ENGINE FOR MORE THAN 10 SECONDS
4.CRANK ENGINE FOR MORE THAN 10 SECONDS
Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC* (ECM)
5.CHECK FOR DTC* (ECM)
a.

Check for DTCs and note any codes that are output.

i.

for 8NR-FTS:

Powertrain > Engine > Trouble Codes
50001 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Trouble Codes
50001 234


HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.


Result:
Result Proceed to
DTCs are not output A
SFI system DTCs are output (for 8NR-FTS) B
SFI system DTCs are output (for 3ZR-FAE) C
Immobiliser system DTCs are output D



A

6.CHECK FOR DTC* (TRANSPONDER KEY ECU ASSEMBLY)

B

C

D

6.CHECK FOR DTC* (TRANSPONDER KEY ECU ASSEMBLY)
a.

Check for DTCs and note any codes that are output.

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.



Result:
Result Proceed to
DTCs are not output A
Immobiliser system DTCs are output B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.REPAIR OR REPLACE
8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.REPAIR OR REPLACE
9.REPAIR OR REPLACE
HINT:

If the transponder key ECU assembly, ECM, or key are replaced, refer to Service Bulletin.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR DTC*
10.CHECK FOR DTC*
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260
i.

for 8NR-FTS:

Powertrain > Engine > Clear DTCs
50002 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Trouble Codes
50001 234


b.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
i.

for 8NR-FTS:

Powertrain > Engine > Trouble Codes
50001 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Trouble Codes
50001 234


HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.


Result:
Result Proceed to
DTCs are not output A
Immobiliser system DTCs are output B



A

END

B