Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM (w/ Steering Control) › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297892 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  U023A  Lost Communication with Front Camera Module  


DESCRIPTION

When a communication error between the forward recognition camera and the power steering ECU assembly is detected, the forward recognition camera notifies other ECUs and DTC U023A is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023A Lost Communication with Front Camera Module When the vehicle is being driven at a speed of 5 km/h (3 mph) or more 2 seconds after the ignition switch is turned ON, a communication malfunction between the forward recognition camera and the power steering ECU assembly is detected for 5 seconds or more.
·

CAN communication system

·

Forward recognition camera

·

Power steering ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

The lane departure alert system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (POWER STEERING SYSTEM)
HINT:

When the lane departure alert system outputs DTC U023A, the power steering system may also output DTC U023A. If DTC U023A is output, perform diagnosis for the power steering system first.


a.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTC U023A is not output A
DTC U023A is output B



A

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

B

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the ignition switch to ON and wait 7 seconds or more.

2.

Drive the vehicle at a speed of 5 km/h (3 mph) or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM (w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC U023A is not output A
DTC U023A is output B



A

B

3.REPLACE FORWARD RECOGNITION CAMERA
3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

b.

Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the ignition switch to ON and wait 7 seconds or more.

2.

Drive the vehicle at a speed of 5 km/h (3 mph) or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM (w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC U023A is not output A
DTC U023A is output (for LHD) B
DTC U023A is output (for RHD) C



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY